1 files changed, 5 insertions, 5 deletions
diff --git a/converter/m0110_usb/README.md b/converter/m0110_usb/README.md
index b3fb8f7e9..1c344f1ac 100644
--- a/converter/m0110_usb/README.md
+++ b/converter/m0110_usb/README.md
@@ -2,7 +2,7 @@ M0110/M0110A to USB keyboard converter
 ======================================
 This firmware converts the protocol of Apple Macintosh keyboard **M0110**, **M0110A** and **M0120** into USB. Target of this project is USB AVR controller **ATmega32U4**. Using this converter you can revive these retro keyboards with modern computer.
-Pics of **M0110 + M0120** and **M0110A**.
+Pictures of **M0110 + M0120** and **M0110A**.
 ![M0110+M0120](http://i.imgur.com/dyvXb2Tm.jpg)
 ![M0110A](http://i.imgur.com/HuHOEoHm.jpg)
@@ -31,7 +31,7 @@ Note that original cable used with Mac is **straight** while phone handset cable
 <http://en.wikipedia.org/wiki/Modular_connector#4P4C>
-Close-up pic of handset cable. You can see one end of plug has reverse color codes against the other. Click to enlarge.
+Close-up picture of handset cable. You can see one end of plug has reverse color codes against the other. Click to enlarge.
 [![4P4C cable](http://i.imgur.com/3S9P1mYm.jpg?1)](http://i.imgur.com/3S9P1mY.jpg?1)
 [Teensy]: http://www.pjrc.com/teensy/
@@ -43,12 +43,12 @@ Close-up pic of handset cable. You can see one end of plug has reverse color cod
 ![Jack fig](http://www.kbdbabel.org/conn/kbd_connector_macplus.png)
-### Pull-up Registor
+### Pull-up Resistor
-You may need pull-up registors on signal lines(`CLOCK`, `DATA`) in particular when you have long or coiled cable. **1k-10k Ohm** will be OK for this purpose. In that case the converter may not read signal from keyboard correctly without pull-up resistors.
+You may need pull-up resistors on signal lines(`CLOCK`, `DATA`) in particular when you have long or coiled cable. **1k-10k Ohm** will be OK for this purpose. In that case the converter may not read signal from keyboard correctly without pull-up resistors.
-Building Frimware
+Building Firmware
 -----------------
 To compile firmware you need AVR GCC. You can edit *Makefile* and *config.h* to change compile options and pin configuration.

diff --git a/converter/m0110_usb/README.md b/converter/m0110_usb/README.md index b3fb8f7e9..1c344f1ac 100644 --- a/converter/m0110_usb/README.md +++ b/converter/m0110_usb/README.md
@@ -2,7 +2,7 @@ M0110/M0110A to USB keyboard converter
2	======================================	2	======================================
3	This firmware converts the protocol of Apple Macintosh keyboard M0110, M0110A and M0120 into USB. Target of this project is USB AVR controller ATmega32U4. Using this converter you can revive these retro keyboards with modern computer.	3	This firmware converts the protocol of Apple Macintosh keyboard M0110, M0110A and M0120 into USB. Target of this project is USB AVR controller ATmega32U4. Using this converter you can revive these retro keyboards with modern computer.
4		4
5	Pics of M0110 + M0120 and M0110A.	5	Pictures of M0110 + M0120 and M0110A.
6		6
7	![M0110+M0120](http://i.imgur.com/dyvXb2Tm.jpg)	7	![M0110+M0120](http://i.imgur.com/dyvXb2Tm.jpg)
8	![M0110A](http://i.imgur.com/HuHOEoHm.jpg)	8	![M0110A](http://i.imgur.com/HuHOEoHm.jpg)
@@ -31,7 +31,7 @@ Note that original cable used with Mac is straight while phone handset cable
31		31
32	<http://en.wikipedia.org/wiki/Modular_connector#4P4C>	32	<http://en.wikipedia.org/wiki/Modular_connector#4P4C>
33		33
34	Close-up pic of handset cable. You can see one end of plug has reverse color codes against the other. Click to enlarge.	34	Close-up picture of handset cable. You can see one end of plug has reverse color codes against the other. Click to enlarge.
35	[![4P4C cable](http://i.imgur.com/3S9P1mYm.jpg?1)](http://i.imgur.com/3S9P1mY.jpg?1)	35	[![4P4C cable](http://i.imgur.com/3S9P1mYm.jpg?1)](http://i.imgur.com/3S9P1mY.jpg?1)
36		36
37	[Teensy]: http://www.pjrc.com/teensy/	37	[Teensy]: http://www.pjrc.com/teensy/
@@ -43,12 +43,12 @@ Close-up pic of handset cable. You can see one end of plug has reverse color cod
43	![Jack fig](http://www.kbdbabel.org/conn/kbd_connector_macplus.png)	43	![Jack fig](http://www.kbdbabel.org/conn/kbd_connector_macplus.png)
44		44
45		45
46	### Pull-up Registor	46	### Pull-up Resistor
47	You may need pull-up registors on signal lines(`CLOCK`, `DATA`) in particular when you have long or coiled cable. 1k-10k Ohm will be OK for this purpose. In that case the converter may not read signal from keyboard correctly without pull-up resistors.	47	You may need pull-up resistors on signal lines(`CLOCK`, `DATA`) in particular when you have long or coiled cable. 1k-10k Ohm will be OK for this purpose. In that case the converter may not read signal from keyboard correctly without pull-up resistors.
48		48
49		49
50		50
51	Building Frimware	51	Building Firmware
52	-----------------	52	-----------------
53	To compile firmware you need AVR GCC. You can edit Makefile and config.h to change compile options and pin configuration.	53	To compile firmware you need AVR GCC. You can edit Makefile and config.h to change compile options and pin configuration.
54		54