4 files changed, 11 insertions, 0 deletions

diff --git a/docs/feature_rgb_matrix.md b/docs/feature_rgb_matrix.md
index fd866bd57..878acaf8b 100644
--- a/docs/feature_rgb_matrix.md
+++ b/docs/feature_rgb_matrix.md
@@ -439,6 +439,8 @@ These are defined in [`rgblight_list.h`](https://github.com/qmk/qmk_firmware/blo
 #define RGB_MATRIX_STARTUP_VAL RGB_MATRIX_MAXIMUM_BRIGHTNESS // Sets the default brightness value, if none has been set
 #define RGB_MATRIX_STARTUP_SPD 127 // Sets the default animation speed, if none has been set
 #define RGB_MATRIX_DISABLE_KEYCODES // disables control of rgb matrix by keycodes (must use code functions to control the feature)
+#define RGB_MATRIX_SPLIT { X, Y }       // (Optional) For split keyboards, the number of LEDs connected on each half. X = left, Y = Right.
+                                        // If RGB_MATRIX_KEYPRESSES or RGB_MATRIX_KEYRELEASES is enabled, you also will want to enable SPLIT_TRANSPORT_MIRROR
 ```
 
 ## EEPROM storage :id=eeprom-storage
diff --git a/docs/keycodes.md b/docs/keycodes.md
index 9acf8b683..f3c519b13 100644
--- a/docs/keycodes.md
+++ b/docs/keycodes.md
@@ -516,6 +516,9 @@ See also: [One Shot Keys](one_shot_keys.md)
 |------------|----------------------------------|
 |`OSM(mod)`  |Hold `mod` for one keypress       |
 |`OSL(layer)`|Switch to `layer` for one keypress|
+|`OS_ON`     |Turns One Shot keys on            |
+|`OS_OFF`    |Turns One Shot keys off           |
+|`OS_TOGG`   |Toggles One Shot keys status      |
 
 ## Space Cadet :id=space-cadet
 
diff --git a/docs/one_shot_keys.md b/docs/one_shot_keys.md
index 9a082d7d6..9fc548629 100644
--- a/docs/one_shot_keys.md
+++ b/docs/one_shot_keys.md
@@ -17,6 +17,9 @@ You can control the behavior of one shot keys by defining these in `config.h`:
 
 * `OSM(mod)` - Momentarily hold down *mod*. You must use the `MOD_*` keycodes as shown in [Mod Tap](mod_tap.md), not the `KC_*` codes.
 * `OSL(layer)` - momentary switch to *layer*.
+* `OS_ON` - Turns on One Shot keys.
+* `OS_OFF` - Turns off One Shot keys. OSM act as regular mod keys, OSL act like `MO`.
+* `ON_TOGG` - Toggles the one shot key status.
 
 Sometimes, you want to activate a one-shot key as part of a macro or tap dance routine.  
 
diff --git a/docs/ws2812_driver.md b/docs/ws2812_driver.md
index cca6827ec..fa14f02fd 100644
--- a/docs/ws2812_driver.md
+++ b/docs/ws2812_driver.md
@@ -102,11 +102,14 @@ Configure the hardware via your config.h:
 #define WS2812_PWM_DRIVER PWMD2  // default: PWMD2
 #define WS2812_PWM_CHANNEL 2  // default: 2
 #define WS2812_PWM_PAL_MODE 2  // Pin "alternate function", see the respective datasheet for the appropriate values for your MCU. default: 2
+//#define WS2812_PWM_COMPLEMENTARY_OUTPUT // Define for a complementary timer output (TIMx_CHyN); omit for a normal timer output (TIMx_CHy).
 #define WS2812_DMA_STREAM STM32_DMA1_STREAM2  // DMA Stream for TIMx_UP, see the respective reference manual for the appropriate values for your MCU.
 #define WS2812_DMA_CHANNEL 2  // DMA Channel for TIMx_UP, see the respective reference manual for the appropriate values for your MCU.
 #define WS2812_DMAMUX_ID STM32_DMAMUX1_TIM2_UP // DMAMUX configuration for TIMx_UP -- only required if your MCU has a DMAMUX peripheral, see the respective reference manual for the appropriate values for your MCU.
 ```
 
+Note that using a complementary timer output (TIMx_CHyN) is possible only for advanced-control timers (TIM1, TIM8, TIM20 on STM32), and the `STM32_PWM_USE_ADVANCED` option in mcuconf.h must be set to `TRUE`.  Complementary outputs of general-purpose timers are not supported due to ChibiOS limitations.
+
 You must also turn on the PWM feature in your halconf.h and mcuconf.h
 
 #### Testing Notes