diff options
Diffstat (limited to 'keyboard/hhkb/Makefile.tmk')
| -rw-r--r-- | keyboard/hhkb/Makefile.tmk | 129 |
1 files changed, 0 insertions, 129 deletions
diff --git a/keyboard/hhkb/Makefile.tmk b/keyboard/hhkb/Makefile.tmk deleted file mode 100644 index d3730081f..000000000 --- a/keyboard/hhkb/Makefile.tmk +++ /dev/null | |||
| @@ -1,129 +0,0 @@ | |||
| 1 | #---------------------------------------------------------------------------- | ||
| 2 | # On command line: | ||
| 3 | # | ||
| 4 | # make all = Make software. | ||
| 5 | # | ||
| 6 | # make clean = Clean out built project files. | ||
| 7 | # | ||
| 8 | # make coff = Convert ELF to AVR COFF. | ||
| 9 | # | ||
| 10 | # make extcoff = Convert ELF to AVR Extended COFF. | ||
| 11 | # | ||
| 12 | # make program = Download the hex file to the device. | ||
| 13 | # Please customize your programmer settings(PROGRAM_CMD) | ||
| 14 | # | ||
| 15 | # make teensy = Download the hex file to the device, using teensy_loader_cli. | ||
| 16 | # (must have teensy_loader_cli installed). | ||
| 17 | # | ||
| 18 | # make dfu = Download the hex file to the device, using dfu-programmer (must | ||
| 19 | # have dfu-programmer installed). | ||
| 20 | # | ||
| 21 | # make flip = Download the hex file to the device, using Atmel FLIP (must | ||
| 22 | # have Atmel FLIP installed). | ||
| 23 | # | ||
| 24 | # make dfu-ee = Download the eeprom file to the device, using dfu-programmer | ||
| 25 | # (must have dfu-programmer installed). | ||
| 26 | # | ||
| 27 | # make flip-ee = Download the eeprom file to the device, using Atmel FLIP | ||
| 28 | # (must have Atmel FLIP installed). | ||
| 29 | # | ||
| 30 | # make debug = Start either simulavr or avarice as specified for debugging, | ||
| 31 | # with avr-gdb or avr-insight as the front end for debugging. | ||
| 32 | # | ||
| 33 | # make filename.s = Just compile filename.c into the assembler code only. | ||
| 34 | # | ||
| 35 | # make filename.i = Create a preprocessed source file for use in submitting | ||
| 36 | # bug reports to the GCC project. | ||
| 37 | # | ||
| 38 | # To rebuild project do "make clean" then "make all". | ||
| 39 | #---------------------------------------------------------------------------- | ||
| 40 | |||
| 41 | # Target file name (without extension). | ||
| 42 | TARGET = hhkb_tmk | ||
| 43 | |||
| 44 | # Directory common source filess exist | ||
| 45 | TOP_DIR = ../.. | ||
| 46 | |||
| 47 | # Directory keyboard dependent files exist | ||
| 48 | TARGET_DIR = . | ||
| 49 | |||
| 50 | |||
| 51 | # List C source files here. (C dependencies are automatically generated.) | ||
| 52 | SRC += keymap.c \ | ||
| 53 | matrix.c \ | ||
| 54 | led.c | ||
| 55 | |||
| 56 | CONFIG_H = config.h | ||
| 57 | |||
| 58 | |||
| 59 | # MCU name | ||
| 60 | #MCU = at90usb1286 | ||
| 61 | MCU = atmega32u4 | ||
| 62 | |||
| 63 | # Processor frequency. | ||
| 64 | # This will define a symbol, F_CPU, in all source code files equal to the | ||
| 65 | # processor frequency in Hz. You can then use this symbol in your source code to | ||
| 66 | # calculate timings. Do NOT tack on a 'UL' at the end, this will be done | ||
| 67 | # automatically to create a 32-bit value in your source code. | ||
| 68 | # | ||
| 69 | # This will be an integer division of F_USB below, as it is sourced by | ||
| 70 | # F_USB after it has run through any CPU prescalers. Note that this value | ||
| 71 | # does not *change* the processor frequency - it should merely be updated to | ||
| 72 | # reflect the processor speed set externally so that the code can use accurate | ||
| 73 | # software delays. | ||
| 74 | F_CPU = 16000000 | ||
| 75 | |||
| 76 | |||
| 77 | # | ||
| 78 | # LUFA specific | ||
| 79 | # | ||
| 80 | # Target architecture (see library "Board Types" documentation). | ||
| 81 | ARCH = AVR8 | ||
| 82 | |||
| 83 | # Input clock frequency. | ||
| 84 | # This will define a symbol, F_USB, in all source code files equal to the | ||
| 85 | # input clock frequency (before any prescaling is performed) in Hz. This value may | ||
| 86 | # differ from F_CPU if prescaling is used on the latter, and is required as the | ||
| 87 | # raw input clock is fed directly to the PLL sections of the AVR for high speed | ||
| 88 | # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | ||
| 89 | # at the end, this will be done automatically to create a 32-bit value in your | ||
| 90 | # source code. | ||
| 91 | # | ||
| 92 | # If no clock division is performed on the input clock inside the AVR (via the | ||
| 93 | # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | ||
| 94 | F_USB = $(F_CPU) | ||
| 95 | |||
| 96 | # Interrupt driven control endpoint task | ||
| 97 | OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | ||
| 98 | |||
| 99 | |||
| 100 | # Boot Section Size in *bytes* | ||
| 101 | # Teensy halfKay 512 | ||
| 102 | # Teensy++ halfKay 1024 | ||
| 103 | # Atmel DFU loader 4096 | ||
| 104 | # LUFA bootloader 4096 | ||
| 105 | # USBaspLoader 2048 | ||
| 106 | OPT_DEFS += -DBOOTLOADER_SIZE=4096 | ||
| 107 | |||
| 108 | |||
| 109 | # Build Options | ||
| 110 | # comment out to disable the options. | ||
| 111 | # | ||
| 112 | #BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration | ||
| 113 | MOUSEKEY_ENABLE = yes # Mouse keys | ||
| 114 | EXTRAKEY_ENABLE = yes # Audio control and System control | ||
| 115 | CONSOLE_ENABLE = yes # Console for debug | ||
| 116 | COMMAND_ENABLE = yes # Commands for debug and configuration | ||
| 117 | #NKRO_ENABLE = yes # USB Nkey Rollover | ||
| 118 | |||
| 119 | |||
| 120 | # Search Path | ||
| 121 | VPATH += $(TARGET_DIR) | ||
| 122 | VPATH += $(TOP_DIR) | ||
| 123 | |||
| 124 | include $(TOP_DIR)/protocol/lufa.mk | ||
| 125 | include $(TOP_DIR)/common.mk | ||
| 126 | include $(TOP_DIR)/rules.mk | ||
| 127 | |||
| 128 | debug-on: EXTRAFLAGS += -DDEBUG | ||
| 129 | debug-on: all | ||