diff options
Diffstat (limited to 'keyboards/aeboards/aegis/rules.mk')
| -rw-r--r-- | keyboards/aeboards/aegis/rules.mk | 53 |
1 files changed, 11 insertions, 42 deletions
diff --git a/keyboards/aeboards/aegis/rules.mk b/keyboards/aeboards/aegis/rules.mk index f1c632289..602da8678 100644 --- a/keyboards/aeboards/aegis/rules.mk +++ b/keyboards/aeboards/aegis/rules.mk | |||
| @@ -1,50 +1,16 @@ | |||
| 1 | # project specific files | ||
| 2 | SRC = keyboards/wilba_tech/wt_main.c | ||
| 3 | |||
| 4 | # MCU name | 1 | # MCU name |
| 5 | MCU = atmega32u4 | 2 | MCU = atmega32u4 |
| 6 | 3 | ||
| 7 | # Processor frequency. | 4 | # Bootloader selection |
| 8 | # This will define a symbol, F_CPU, in all source code files equal to the | 5 | # Teensy halfkay |
| 9 | # processor frequency in Hz. You can then use this symbol in your source code to | 6 | # Pro Micro caterina |
| 10 | # calculate timings. Do NOT tack on a 'UL' at the end, this will be done | 7 | # Atmel DFU atmel-dfu |
| 11 | # automatically to create a 32-bit value in your source code. | 8 | # LUFA DFU lufa-dfu |
| 12 | # | 9 | # QMK DFU qmk-dfu |
| 13 | # This will be an integer division of F_USB below, as it is sourced by | 10 | # ATmega32A bootloadHID |
| 14 | # F_USB after it has run through any CPU prescalers. Note that this value | 11 | # ATmega328P USBasp |
| 15 | # does not *change* the processor frequency - it should merely be updated to | ||
| 16 | # reflect the processor speed set externally so that the code can use accurate | ||
| 17 | # software delays. | ||
| 18 | F_CPU = 16000000 | ||
| 19 | |||
| 20 | |||
| 21 | # | ||
| 22 | # LUFA specific | ||
| 23 | # | ||
| 24 | # Target architecture (see library "Board Types" documentation). | ||
| 25 | ARCH = AVR8 | ||
| 26 | |||
| 27 | # Input clock frequency. | ||
| 28 | # This will define a symbol, F_USB, in all source code files equal to the | ||
| 29 | # input clock frequency (before any prescaling is performed) in Hz. This value may | ||
| 30 | # differ from F_CPU if prescaling is used on the latter, and is required as the | ||
| 31 | # raw input clock is fed directly to the PLL sections of the AVR for high speed | ||
| 32 | # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | ||
| 33 | # at the end, this will be done automatically to create a 32-bit value in your | ||
| 34 | # source code. | ||
| 35 | # | ||
| 36 | # If no clock division is performed on the input clock inside the AVR (via the | ||
| 37 | # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | ||
| 38 | F_USB = $(F_CPU) | ||
| 39 | |||
| 40 | # Interrupt driven control endpoint task(+60) | ||
| 41 | OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | ||
| 42 | |||
| 43 | |||
| 44 | # Boot Section | ||
| 45 | BOOTLOADER = atmel-dfu | 12 | BOOTLOADER = atmel-dfu |
| 46 | 13 | ||
| 47 | |||
| 48 | # Build Options | 14 | # Build Options |
| 49 | # change yes to no to disable | 15 | # change yes to no to disable |
| 50 | # | 16 | # |
| @@ -63,3 +29,6 @@ UNICODE_ENABLE = no # Unicode | |||
| 63 | BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID | 29 | BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID |
| 64 | AUDIO_ENABLE = no # Audio output on port C6 | 30 | AUDIO_ENABLE = no # Audio output on port C6 |
| 65 | FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches | 31 | FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches |
| 32 | |||
| 33 | # project specific files | ||
| 34 | SRC = keyboards/wilba_tech/wt_main.c | ||