3 files changed, 76 insertions, 75 deletions
diff --git a/keyboards/arrow_pad/Makefile b/keyboards/arrow_pad/Makefile
index 09fcf3e7a..4e2a6f00f 100644
--- a/keyboards/arrow_pad/Makefile
+++ b/keyboards/arrow_pad/Makefile
@@ -1,74 +1,3 @@
+ifndef MAKEFILE_INCLUDED
-# MCU name
-#MCU = at90usb1287
-MCU = atmega32u4
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=512
-# Build Options
-#   change yes to no to disable
-#
-BOOTMAGIC_ENABLE ?= yes      # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE ?= yes       # Mouse keys(+4700)
-EXTRAKEY_ENABLE ?= yes       # Audio control and System control(+450)
-CONSOLE_ENABLE ?= yes        # Console for debug(+400)
-COMMAND_ENABLE ?= yes        # Commands for debug and configuration
-KEYBOARD_LOCK_ENABLE ?= yes  # Allow locking of keyboard via magic key
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE ?= no       # Breathing sleep LED during USB suspend
-# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-NKRO_ENABLE ?= yes           # USB Nkey Rollover
-BACKLIGHT_ENABLE ?= yes      # Enable keyboard backlight functionality
-MIDI_ENABLE ?= no            # MIDI controls
-UNICODE_ENABLE ?= no         # Unicode
-BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID
-AUDIO_ENABLE ?= no           # Audio output on port C6
-ifndef QUANTUM_DIR
        include ../../Makefile
 endif
 \ No newline at end of file
diff --git a/keyboards/arrow_pad/readme.md b/keyboards/arrow_pad/readme.md
index 5aa44cce5..2e9a64f2e 100644
--- a/keyboards/arrow_pad/readme.md
+++ b/keyboards/arrow_pad/readme.md
@@ -12,13 +12,15 @@ Download or clone the whole firmware and navigate to the keyboards/arrow_pad fol
 Depending on which keymap you would like to use, you will have to compile slightly differently.
 ### Default
-To build with the default keymap, simply run `make`.
+To build with the default keymap, simply run `make default`.
 ### Other Keymaps
 Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `<name>.c` in the keymaps folder, and see keymap document (you can find in top readme.md) and existent keymap files.
-To build the firmware binary hex file with a keymap just do `make` with `KEYMAP` option like:
+To build the firmware binary hex file with a keymap just do `make` with a keymap like this:
 ```
-$ make KEYMAP=[default|jack|<name>]
+$ make [default|jack|<name>]
 ```
 Keymaps follow the format **__\<name\>.c__** and are stored in the `keymaps` folder.
 \ No newline at end of file
diff --git a/keyboards/arrow_pad/rules.mk b/keyboards/arrow_pad/rules.mk
new file mode 100644
index 000000000..3dca9b6ea
--- /dev/null
+++ b/keyboards/arrow_pad/rules.mk
@@ -0,0 +1,70 @@
+# MCU name
+#MCU = at90usb1287
+MCU = atmega32u4
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=512
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE ?= yes      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes       # Audio control and System control(+450)
+CONSOLE_ENABLE ?= yes        # Console for debug(+400)
+COMMAND_ENABLE ?= yes        # Commands for debug and configuration
+KEYBOARD_LOCK_ENABLE ?= yes  # Allow locking of keyboard via magic key
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE ?= no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE ?= yes           # USB Nkey Rollover
+BACKLIGHT_ENABLE ?= yes      # Enable keyboard backlight functionality
+MIDI_ENABLE ?= no            # MIDI controls
+UNICODE_ENABLE ?= no         # Unicode
+BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE ?= no           # Audio output on port C6
+\ No newline at end of file

diff --git a/keyboards/arrow_pad/Makefile b/keyboards/arrow_pad/Makefile index 09fcf3e7a..4e2a6f00f 100644 --- a/keyboards/arrow_pad/Makefile +++ b/keyboards/arrow_pad/Makefile
@@ -1,74 +1,3 @@
1		1	ifndef MAKEFILE_INCLUDED
2
3	# MCU name
4	#MCU = at90usb1287
5	MCU = atmega32u4
6
7	# Processor frequency.
8	# This will define a symbol, F_CPU, in all source code files equal to the
9	# processor frequency in Hz. You can then use this symbol in your source code to
10	# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
11	# automatically to create a 32-bit value in your source code.
12	#
13	# This will be an integer division of F_USB below, as it is sourced by
14	# F_USB after it has run through any CPU prescalers. Note that this value
15	# does not change the processor frequency - it should merely be updated to
16	# reflect the processor speed set externally so that the code can use accurate
17	# software delays.
18	F_CPU = 16000000
19
20
21	#
22	# LUFA specific
23	#
24	# Target architecture (see library "Board Types" documentation).
25	ARCH = AVR8
26
27	# Input clock frequency.
28	# This will define a symbol, F_USB, in all source code files equal to the
29	# input clock frequency (before any prescaling is performed) in Hz. This value may
30	# differ from F_CPU if prescaling is used on the latter, and is required as the
31	# raw input clock is fed directly to the PLL sections of the AVR for high speed
32	# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
33	# at the end, this will be done automatically to create a 32-bit value in your
34	# source code.
35	#
36	# If no clock division is performed on the input clock inside the AVR (via the
37	# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
38	F_USB = $(F_CPU)
39
40	# Interrupt driven control endpoint task(+60)
41	OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
42
43
44	# Boot Section Size in bytes
45	# Teensy halfKay 512
46	# Teensy++ halfKay 1024
47	# Atmel DFU loader 4096
48	# LUFA bootloader 4096
49	# USBaspLoader 2048
50	OPT_DEFS += -DBOOTLOADER_SIZE=512
51
52
53	# Build Options
54	# change yes to no to disable
55	#
56	BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000)
57	MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
58	EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
59	CONSOLE_ENABLE ?= yes # Console for debug(+400)
60	COMMAND_ENABLE ?= yes # Commands for debug and configuration
61	KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key
62	# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
63	SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend
64	# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
65	NKRO_ENABLE ?= yes # USB Nkey Rollover
66	BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality
67	MIDI_ENABLE ?= no # MIDI controls
68	UNICODE_ENABLE ?= no # Unicode
69	BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
70	AUDIO_ENABLE ?= no # Audio output on port C6
71
72	ifndef QUANTUM_DIR
73	include ../../Makefile	2	include ../../Makefile
74	endif \ No newline at end of file	3	endif \ No newline at end of file


diff --git a/keyboards/arrow_pad/readme.md b/keyboards/arrow_pad/readme.md index 5aa44cce5..2e9a64f2e 100644 --- a/keyboards/arrow_pad/readme.md +++ b/keyboards/arrow_pad/readme.md
@@ -12,13 +12,15 @@ Download or clone the whole firmware and navigate to the keyboards/arrow_pad fol
12	Depending on which keymap you would like to use, you will have to compile slightly differently.	12	Depending on which keymap you would like to use, you will have to compile slightly differently.
13		13
14	### Default	14	### Default
15	To build with the default keymap, simply run `make`.	15	To build with the default keymap, simply run `make default`.
16		16
17	### Other Keymaps	17	### Other Keymaps
18	Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `<name>.c` in the keymaps folder, and see keymap document (you can find in top readme.md) and existent keymap files.	18	Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `<name>.c` in the keymaps folder, and see keymap document (you can find in top readme.md) and existent keymap files.
19		19
20	To build the firmware binary hex file with a keymap just do `make` with `KEYMAP` option like:	20	To build the firmware binary hex file with a keymap just do `make` with a keymap like this:
		21
21	```	22	```
22	$ make KEYMAP=[default\|jack\|<name>]	23	$ make [default\|jack\|<name>]
23	```	24	```
		25
24	Keymaps follow the format __\<name\>.c__ and are stored in the `keymaps` folder. \ No newline at end of file	26	Keymaps follow the format __\<name\>.c__ and are stored in the `keymaps` folder. \ No newline at end of file


diff --git a/keyboards/arrow_pad/rules.mk b/keyboards/arrow_pad/rules.mk new file mode 100644 index 000000000..3dca9b6ea --- /dev/null +++ b/keyboards/arrow_pad/rules.mk
@@ -0,0 +1,70 @@
		1
		2
		3	# MCU name
		4	#MCU = at90usb1287
		5	MCU = atmega32u4
		6
		7	# Processor frequency.
		8	# This will define a symbol, F_CPU, in all source code files equal to the
		9	# processor frequency in Hz. You can then use this symbol in your source code to
		10	# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
		11	# automatically to create a 32-bit value in your source code.
		12	#
		13	# This will be an integer division of F_USB below, as it is sourced by
		14	# F_USB after it has run through any CPU prescalers. Note that this value
		15	# does not change the processor frequency - it should merely be updated to
		16	# reflect the processor speed set externally so that the code can use accurate
		17	# software delays.
		18	F_CPU = 16000000
		19
		20
		21	#
		22	# LUFA specific
		23	#
		24	# Target architecture (see library "Board Types" documentation).
		25	ARCH = AVR8
		26
		27	# Input clock frequency.
		28	# This will define a symbol, F_USB, in all source code files equal to the
		29	# input clock frequency (before any prescaling is performed) in Hz. This value may
		30	# differ from F_CPU if prescaling is used on the latter, and is required as the
		31	# raw input clock is fed directly to the PLL sections of the AVR for high speed
		32	# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
		33	# at the end, this will be done automatically to create a 32-bit value in your
		34	# source code.
		35	#
		36	# If no clock division is performed on the input clock inside the AVR (via the
		37	# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
		38	F_USB = $(F_CPU)
		39
		40	# Interrupt driven control endpoint task(+60)
		41	OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
		42
		43
		44	# Boot Section Size in bytes
		45	# Teensy halfKay 512
		46	# Teensy++ halfKay 1024
		47	# Atmel DFU loader 4096
		48	# LUFA bootloader 4096
		49	# USBaspLoader 2048
		50	OPT_DEFS += -DBOOTLOADER_SIZE=512
		51
		52
		53	# Build Options
		54	# change yes to no to disable
		55	#
		56	BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000)
		57	MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
		58	EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
		59	CONSOLE_ENABLE ?= yes # Console for debug(+400)
		60	COMMAND_ENABLE ?= yes # Commands for debug and configuration
		61	KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key
		62	# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
		63	SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend
		64	# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
		65	NKRO_ENABLE ?= yes # USB Nkey Rollover
		66	BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality
		67	MIDI_ENABLE ?= no # MIDI controls
		68	UNICODE_ENABLE ?= no # Unicode
		69	BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
		70	AUDIO_ENABLE ?= no # Audio output on port C6 \ No newline at end of file