diff options
Diffstat (limited to 'keyboards/atomic/rules.mk')
| -rw-r--r-- | keyboards/atomic/rules.mk | 52 |
1 files changed, 9 insertions, 43 deletions
diff --git a/keyboards/atomic/rules.mk b/keyboards/atomic/rules.mk index 2f9e2e713..8ccbcb11b 100644 --- a/keyboards/atomic/rules.mk +++ b/keyboards/atomic/rules.mk | |||
| @@ -1,49 +1,15 @@ | |||
| 1 | # MCU name | 1 | # MCU name |
| 2 | MCU = atmega32u4 | 2 | MCU = atmega32u4 |
| 3 | 3 | ||
| 4 | # Processor frequency. | 4 | # Bootloader selection |
| 5 | # This will define a symbol, F_CPU, in all source code files equal to the | 5 | # Teensy halfkay |
| 6 | # processor frequency in Hz. You can then use this symbol in your source code to | 6 | # Pro Micro caterina |
| 7 | # calculate timings. Do NOT tack on a 'UL' at the end, this will be done | 7 | # Atmel DFU atmel-dfu |
| 8 | # automatically to create a 32-bit value in your source code. | 8 | # LUFA DFU lufa-dfu |
| 9 | # | 9 | # QMK DFU qmk-dfu |
| 10 | # This will be an integer division of F_USB below, as it is sourced by | 10 | # ATmega32A bootloadHID |
| 11 | # F_USB after it has run through any CPU prescalers. Note that this value | 11 | # ATmega328P USBasp |
| 12 | # does not *change* the processor frequency - it should merely be updated to | 12 | BOOTLOADER = atmel-dfu |
| 13 | # reflect the processor speed set externally so that the code can use accurate | ||
| 14 | # software delays. | ||
| 15 | F_CPU = 16000000 | ||
| 16 | |||
| 17 | # | ||
| 18 | # LUFA specific | ||
| 19 | # | ||
| 20 | # Target architecture (see library "Board Types" documentation). | ||
| 21 | ARCH = AVR8 | ||
| 22 | |||
| 23 | # Input clock frequency. | ||
| 24 | # This will define a symbol, F_USB, in all source code files equal to the | ||
| 25 | # input clock frequency (before any prescaling is performed) in Hz. This value may | ||
| 26 | # differ from F_CPU if prescaling is used on the latter, and is required as the | ||
| 27 | # raw input clock is fed directly to the PLL sections of the AVR for high speed | ||
| 28 | # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | ||
| 29 | # at the end, this will be done automatically to create a 32-bit value in your | ||
| 30 | # source code. | ||
| 31 | # | ||
| 32 | # If no clock division is performed on the input clock inside the AVR (via the | ||
| 33 | # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | ||
| 34 | F_USB = $(F_CPU) | ||
| 35 | |||
| 36 | # Interrupt driven control endpoint task(+60) | ||
| 37 | OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | ||
| 38 | |||
| 39 | |||
| 40 | # Boot Section Size in *bytes* | ||
| 41 | # Teensy halfKay 512 | ||
| 42 | # Teensy++ halfKay 1024 | ||
| 43 | # Atmel DFU loader 4096 | ||
| 44 | # LUFA bootloader 4096 | ||
| 45 | # USBaspLoader 2048 | ||
| 46 | OPT_DEFS += -DBOOTLOADER_SIZE=4096 | ||
| 47 | 13 | ||
| 48 | # Build Options | 14 | # Build Options |
| 49 | # change to "no" to disable the options, or define them in the Makefile in | 15 | # change to "no" to disable the options, or define them in the Makefile in |