diff options
Diffstat (limited to 'keyboards/cu75/rules.mk')
| -rw-r--r-- | keyboards/cu75/rules.mk | 51 |
1 files changed, 12 insertions, 39 deletions
diff --git a/keyboards/cu75/rules.mk b/keyboards/cu75/rules.mk index a84343f05..697d8d18f 100644 --- a/keyboards/cu75/rules.mk +++ b/keyboards/cu75/rules.mk | |||
| @@ -1,41 +1,14 @@ | |||
| 1 | # MCU name | ||
| 1 | MCU = atmega32u4 | 2 | MCU = atmega32u4 |
| 2 | OPT_DEFS += -DBOOTLOADER_SIZE=4096 | ||
| 3 | 3 | ||
| 4 | 4 | # Bootloader selection | |
| 5 | # Processor frequency. | 5 | # Teensy halfkay |
| 6 | # This will define a symbol, F_CPU, in all source code files equal to the | 6 | # Pro Micro caterina |
| 7 | # processor frequency in Hz. You can then use this symbol in your source code to | 7 | # Atmel DFU atmel-dfu |
| 8 | # calculate timings. Do NOT tack on a 'UL' at the end, this will be done | 8 | # LUFA DFU lufa-dfu |
| 9 | # automatically to create a 32-bit value in your source code. | 9 | # QMK DFU qmk-dfu |
| 10 | # | 10 | # ATmega32A bootloadHID |
| 11 | # This will be an integer division of F_USB below, as it is sourced by | 11 | # ATmega328P USBasp |
| 12 | # F_USB after it has run through any CPU prescalers. Note that this value | 12 | BOOTLOADER = atmel-dfu |
| 13 | # does not *change* the processor frequency - it should merely be updated to | 13 | |
| 14 | # reflect the processor speed set externally so that the code can use accurate | 14 | SRC = ../lfkeyboards/TWIlib.c ../lfkeyboards/issi.c ../lfkeyboards/lighting.c |
| 15 | # software delays. | ||
| 16 | F_CPU = 16000000 | ||
| 17 | |||
| 18 | |||
| 19 | # | ||
| 20 | # LUFA specific | ||
| 21 | # | ||
| 22 | # Target architecture (see library "Board Types" documentation). | ||
| 23 | ARCH = AVR8 | ||
| 24 | |||
| 25 | # Input clock frequency. | ||
| 26 | # This will define a symbol, F_USB, in all source code files equal to the | ||
| 27 | # input clock frequency (before any prescaling is performed) in Hz. This value may | ||
| 28 | # differ from F_CPU if prescaling is used on the latter, and is required as the | ||
| 29 | # raw input clock is fed directly to the PLL sections of the AVR for high speed | ||
| 30 | # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | ||
| 31 | # at the end, this will be done automatically to create a 32-bit value in your | ||
| 32 | # source code. | ||
| 33 | # | ||
| 34 | # If no clock division is performed on the input clock inside the AVR (via the | ||
| 35 | # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | ||
| 36 | F_USB = $(F_CPU) | ||
| 37 | |||
| 38 | # Interrupt driven control endpoint task(+60) | ||
| 39 | OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | ||
| 40 | |||
| 41 | SRC = ../lfkeyboards/TWIlib.c ../lfkeyboards/issi.c ../lfkeyboards/lighting.c \ No newline at end of file | ||