diff options
Diffstat (limited to 'keyboards/mitosis/rules.mk')
-rw-r--r-- | keyboards/mitosis/rules.mk | 63 |
1 files changed, 15 insertions, 48 deletions
diff --git a/keyboards/mitosis/rules.mk b/keyboards/mitosis/rules.mk index 34aa7070f..420c49f9b 100644 --- a/keyboards/mitosis/rules.mk +++ b/keyboards/mitosis/rules.mk | |||
@@ -1,56 +1,16 @@ | |||
1 | |||
2 | OPT_DEFS += -DMITOSIS_PROMICRO | ||
3 | MITOSIS_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \ | ||
4 | avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB) | ||
5 | |||
6 | # # project specific files | ||
7 | SRC = matrix.c | ||
8 | |||
9 | |||
10 | # MCU name | 1 | # MCU name |
11 | MCU = atmega32u4 | 2 | MCU = atmega32u4 |
12 | 3 | ||
13 | # Processor frequency. | 4 | # Bootloader selection |
14 | # This will define a symbol, F_CPU, in all source code files equal to the | 5 | # Teensy halfkay |
15 | # processor frequency in Hz. You can then use this symbol in your source code to | 6 | # Pro Micro caterina |
16 | # calculate timings. Do NOT tack on a 'UL' at the end, this will be done | 7 | # Atmel DFU atmel-dfu |
17 | # automatically to create a 32-bit value in your source code. | 8 | # LUFA DFU lufa-dfu |
18 | # | 9 | # QMK DFU qmk-dfu |
19 | # This will be an integer division of F_USB below, as it is sourced by | 10 | # ATmega32A bootloadHID |
20 | # F_USB after it has run through any CPU prescalers. Note that this value | 11 | # ATmega328P USBasp |
21 | # does not *change* the processor frequency - it should merely be updated to | ||
22 | # reflect the processor speed set externally so that the code can use accurate | ||
23 | # software delays. | ||
24 | F_CPU = 16000000 | ||
25 | |||
26 | # | ||
27 | # LUFA specific | ||
28 | # | ||
29 | # Target architecture (see library "Board Types" documentation). | ||
30 | ARCH = AVR8 | ||
31 | |||
32 | # Input clock frequency. | ||
33 | # This will define a symbol, F_USB, in all source code files equal to the | ||
34 | # input clock frequency (before any prescaling is performed) in Hz. This value may | ||
35 | # differ from F_CPU if prescaling is used on the latter, and is required as the | ||
36 | # raw input clock is fed directly to the PLL sections of the AVR for high speed | ||
37 | # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | ||
38 | # at the end, this will be done automatically to create a 32-bit value in your | ||
39 | # source code. | ||
40 | # | ||
41 | # If no clock division is performed on the input clock inside the AVR (via the | ||
42 | # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | ||
43 | F_USB = $(F_CPU) | ||
44 | |||
45 | # Bootloader | ||
46 | # This definition is optional, and if your keyboard supports multiple bootloaders of | ||
47 | # different sizes, comment this out, and the correct address will be loaded | ||
48 | # automatically (+60). See bootloader.mk for all options. | ||
49 | BOOTLOADER = caterina | 12 | BOOTLOADER = caterina |
50 | 13 | ||
51 | # Interrupt driven control endpoint task(+60) | ||
52 | OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | ||
53 | |||
54 | # Build Options | 14 | # Build Options |
55 | # comment out to disable the options. | 15 | # comment out to disable the options. |
56 | # | 16 | # |
@@ -72,3 +32,10 @@ USB = /dev/ttyACM0 | |||
72 | 32 | ||
73 | # upload: build | 33 | # upload: build |
74 | # $(MITOSIS_UPLOAD_COMMAND) | 34 | # $(MITOSIS_UPLOAD_COMMAND) |
35 | |||
36 | OPT_DEFS += -DMITOSIS_PROMICRO | ||
37 | MITOSIS_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \ | ||
38 | avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB) | ||
39 | |||
40 | # # project specific files | ||
41 | SRC = matrix.c | ||