diff options
Diffstat (limited to 'keyboards/puck/rules.mk')
-rw-r--r-- | keyboards/puck/rules.mk | 52 |
1 files changed, 8 insertions, 44 deletions
diff --git a/keyboards/puck/rules.mk b/keyboards/puck/rules.mk index 48144534d..1bd0b8b1d 100644 --- a/keyboards/puck/rules.mk +++ b/keyboards/puck/rules.mk | |||
@@ -1,50 +1,14 @@ | |||
1 | |||
2 | |||
3 | # MCU name | 1 | # MCU name |
4 | MCU = atmega32u4 | 2 | MCU = atmega32u4 |
5 | 3 | ||
6 | # Processor frequency. | 4 | # Bootloader selection |
7 | # This will define a symbol, F_CPU, in all source code files equal to the | 5 | # Teensy halfkay |
8 | # processor frequency in Hz. You can then use this symbol in your source code to | 6 | # Pro Micro caterina |
9 | # calculate timings. Do NOT tack on a 'UL' at the end, this will be done | 7 | # Atmel DFU atmel-dfu |
10 | # automatically to create a 32-bit value in your source code. | 8 | # LUFA DFU lufa-dfu |
11 | # | 9 | # QMK DFU qmk-dfu |
12 | # This will be an integer division of F_USB below, as it is sourced by | 10 | # ATmega32A bootloadHID |
13 | # F_USB after it has run through any CPU prescalers. Note that this value | 11 | # ATmega328P USBasp |
14 | # does not *change* the processor frequency - it should merely be updated to | ||
15 | # reflect the processor speed set externally so that the code can use accurate | ||
16 | # software delays. | ||
17 | F_CPU = 16000000 | ||
18 | |||
19 | # | ||
20 | # LUFA specific | ||
21 | # | ||
22 | # Target architecture (see library "Board Types" documentation). | ||
23 | ARCH = AVR8 | ||
24 | |||
25 | # Input clock frequency. | ||
26 | # This will define a symbol, F_USB, in all source code files equal to the | ||
27 | # input clock frequency (before any prescaling is performed) in Hz. This value may | ||
28 | # differ from F_CPU if prescaling is used on the latter, and is required as the | ||
29 | # raw input clock is fed directly to the PLL sections of the AVR for high speed | ||
30 | # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | ||
31 | # at the end, this will be done automatically to create a 32-bit value in your | ||
32 | # source code. | ||
33 | # | ||
34 | # If no clock division is performed on the input clock inside the AVR (via the | ||
35 | # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | ||
36 | F_USB = $(F_CPU) | ||
37 | |||
38 | # Interrupt driven control endpoint task(+60) | ||
39 | OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | ||
40 | |||
41 | |||
42 | # Boot Section Size in *bytes* | ||
43 | # Teensy halfKay 512 | ||
44 | # Teensy++ halfKay 1024 | ||
45 | # Atmel DFU loader 4096 | ||
46 | # LUFA bootloader 4096 | ||
47 | # USBaspLoader 2048 | ||
48 | BOOTLOADER = halfkay | 12 | BOOTLOADER = halfkay |
49 | 13 | ||
50 | # Build Options | 14 | # Build Options |