1 files changed, 12 insertions, 43 deletions
diff --git a/keyboards/treadstone48/rules.mk b/keyboards/treadstone48/rules.mk
index 8b0d3cd30..fd3c6df57 100644
--- a/keyboards/treadstone48/rules.mk
+++ b/keyboards/treadstone48/rules.mk
@@ -1,51 +1,16 @@
-SRC += i2c.c
-SRC += serial.c
-SRC += ssd1306.c
 # MCU name
 MCU = atmega32u4
-# Processor frequency.
+# Bootloader selection
-#     This will define a symbol, F_CPU, in all source code files equal to the
+#   Teensy       halfkay
-#     processor frequency in Hz. You can then use this symbol in your source code to
+#   Pro Micro    caterina
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#   Atmel DFU    atmel-dfu
-#     automatically to create a 32-bit value in your source code.
+#   LUFA DFU     lufa-dfu
-#
+#   QMK DFU      qmk-dfu
-#     This will be an integer division of F_USB below, as it is sourced by
+#   ATmega32A    bootloadHID
-#     F_USB after it has run through any CPU prescalers. Note that this value
+#   ATmega328P   USBasp
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-# Bootloader
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
-#     different sizes, comment this out, and the correct address will be loaded
-#     automatically (+60). See bootloader.mk for all options.
 BOOTLOADER = caterina
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
 # Build Options
 #   change to "no" to disable the options, or define them in the Makefile in
 #   the appropriate keymap folder that will get included automatically
@@ -70,3 +35,7 @@ SLEEP_LED_ENABLE = no    # Breathing sleep LED during USB suspend
 CUSTOM_MATRIX = yes
 DEFAULT_FOLDER = treadstone48/rev1
+SRC += i2c.c
+SRC += serial.c
+SRC += ssd1306.c

diff --git a/keyboards/treadstone48/rules.mk b/keyboards/treadstone48/rules.mk index 8b0d3cd30..fd3c6df57 100644 --- a/keyboards/treadstone48/rules.mk +++ b/keyboards/treadstone48/rules.mk
@@ -1,51 +1,16 @@
1	SRC += i2c.c
2	SRC += serial.c
3	SRC += ssd1306.c
4
5	# MCU name	1	# MCU name
6	MCU = atmega32u4	2	MCU = atmega32u4
7		3
8	# Processor frequency.	4	# Bootloader selection
9	# This will define a symbol, F_CPU, in all source code files equal to the	5	# Teensy halfkay
10	# processor frequency in Hz. You can then use this symbol in your source code to	6	# Pro Micro caterina
11	# calculate timings. Do NOT tack on a 'UL' at the end, this will be done	7	# Atmel DFU atmel-dfu
12	# automatically to create a 32-bit value in your source code.	8	# LUFA DFU lufa-dfu
13	#	9	# QMK DFU qmk-dfu
14	# This will be an integer division of F_USB below, as it is sourced by	10	# ATmega32A bootloadHID
15	# F_USB after it has run through any CPU prescalers. Note that this value	11	# ATmega328P USBasp
16	# does not change the processor frequency - it should merely be updated to
17	# reflect the processor speed set externally so that the code can use accurate
18	# software delays.
19	F_CPU = 16000000
20
21	#
22	# LUFA specific
23	#
24	# Target architecture (see library "Board Types" documentation).
25	ARCH = AVR8
26
27	# Input clock frequency.
28	# This will define a symbol, F_USB, in all source code files equal to the
29	# input clock frequency (before any prescaling is performed) in Hz. This value may
30	# differ from F_CPU if prescaling is used on the latter, and is required as the
31	# raw input clock is fed directly to the PLL sections of the AVR for high speed
32	# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
33	# at the end, this will be done automatically to create a 32-bit value in your
34	# source code.
35	#
36	# If no clock division is performed on the input clock inside the AVR (via the
37	# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
38	F_USB = $(F_CPU)
39
40	# Bootloader
41	# This definition is optional, and if your keyboard supports multiple bootloaders of
42	# different sizes, comment this out, and the correct address will be loaded
43	# automatically (+60). See bootloader.mk for all options.
44	BOOTLOADER = caterina	12	BOOTLOADER = caterina
45		13
46	# Interrupt driven control endpoint task(+60)
47	OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
48
49	# Build Options	14	# Build Options
50	# change to "no" to disable the options, or define them in the Makefile in	15	# change to "no" to disable the options, or define them in the Makefile in
51	# the appropriate keymap folder that will get included automatically	16	# the appropriate keymap folder that will get included automatically
@@ -70,3 +35,7 @@ SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
70	CUSTOM_MATRIX = yes	35	CUSTOM_MATRIX = yes
71		36
72	DEFAULT_FOLDER = treadstone48/rev1	37	DEFAULT_FOLDER = treadstone48/rev1
		38
		39	SRC += i2c.c
		40	SRC += serial.c
		41	SRC += ssd1306.c