aboutsummaryrefslogtreecommitdiff
path: root/keyboards
diff options
context:
space:
mode:
Diffstat (limited to 'keyboards')
-rw-r--r--keyboards/ergodox_ez/i2cmaster.h178
-rw-r--r--keyboards/ergodox_ez/twimaster.c208
2 files changed, 0 insertions, 386 deletions
diff --git a/keyboards/ergodox_ez/i2cmaster.h b/keyboards/ergodox_ez/i2cmaster.h
deleted file mode 100644
index 3917b9e6c..000000000
--- a/keyboards/ergodox_ez/i2cmaster.h
+++ /dev/null
@@ -1,178 +0,0 @@
1#ifndef _I2CMASTER_H
2#define _I2CMASTER_H 1
3/*************************************************************************
4* Title: C include file for the I2C master interface
5* (i2cmaster.S or twimaster.c)
6* Author: Peter Fleury <pfleury@gmx.ch> http://jump.to/fleury
7* File: $Id: i2cmaster.h,v 1.10 2005/03/06 22:39:57 Peter Exp $
8* Software: AVR-GCC 3.4.3 / avr-libc 1.2.3
9* Target: any AVR device
10* Usage: see Doxygen manual
11**************************************************************************/
12
13#ifdef DOXYGEN
14/**
15 @defgroup pfleury_ic2master I2C Master library
16 @code #include <i2cmaster.h> @endcode
17
18 @brief I2C (TWI) Master Software Library
19
20 Basic routines for communicating with I2C slave devices. This single master
21 implementation is limited to one bus master on the I2C bus.
22
23 This I2c library is implemented as a compact assembler software implementation of the I2C protocol
24 which runs on any AVR (i2cmaster.S) and as a TWI hardware interface for all AVR with built-in TWI hardware (twimaster.c).
25 Since the API for these two implementations is exactly the same, an application can be linked either against the
26 software I2C implementation or the hardware I2C implementation.
27
28 Use 4.7k pull-up resistor on the SDA and SCL pin.
29
30 Adapt the SCL and SDA port and pin definitions and eventually the delay routine in the module
31 i2cmaster.S to your target when using the software I2C implementation !
32
33 Adjust the CPU clock frequence F_CPU in twimaster.c or in the Makfile when using the TWI hardware implementaion.
34
35 @note
36 The module i2cmaster.S is based on the Atmel Application Note AVR300, corrected and adapted
37 to GNU assembler and AVR-GCC C call interface.
38 Replaced the incorrect quarter period delays found in AVR300 with
39 half period delays.
40
41 @author Peter Fleury pfleury@gmx.ch http://jump.to/fleury
42
43 @par API Usage Example
44 The following code shows typical usage of this library, see example test_i2cmaster.c
45
46 @code
47
48 #include <i2cmaster.h>
49
50
51 #define Dev24C02 0xA2 // device address of EEPROM 24C02, see datasheet
52
53 int main(void)
54 {
55 unsigned char ret;
56
57 i2c_init(); // initialize I2C library
58
59 // write 0x75 to EEPROM address 5 (Byte Write)
60 i2c_start_wait(Dev24C02+I2C_WRITE); // set device address and write mode
61 i2c_write(0x05); // write address = 5
62 i2c_write(0x75); // write value 0x75 to EEPROM
63 i2c_stop(); // set stop conditon = release bus
64
65
66 // read previously written value back from EEPROM address 5
67 i2c_start_wait(Dev24C02+I2C_WRITE); // set device address and write mode
68
69 i2c_write(0x05); // write address = 5
70 i2c_rep_start(Dev24C02+I2C_READ); // set device address and read mode
71
72 ret = i2c_readNak(); // read one byte from EEPROM
73 i2c_stop();
74
75 for(;;);
76 }
77 @endcode
78
79*/
80#endif /* DOXYGEN */
81
82/**@{*/
83
84#if (__GNUC__ * 100 + __GNUC_MINOR__) < 304
85#error "This library requires AVR-GCC 3.4 or later, update to newer AVR-GCC compiler !"
86#endif
87
88#include <avr/io.h>
89
90/** defines the data direction (reading from I2C device) in i2c_start(),i2c_rep_start() */
91#define I2C_READ 1
92
93/** defines the data direction (writing to I2C device) in i2c_start(),i2c_rep_start() */
94#define I2C_WRITE 0
95
96
97/**
98 @brief initialize the I2C master interace. Need to be called only once
99 @param void
100 @return none
101 */
102extern void i2c_init(void);
103
104
105/**
106 @brief Terminates the data transfer and releases the I2C bus
107 @param void
108 @return none
109 */
110extern void i2c_stop(void);
111
112
113/**
114 @brief Issues a start condition and sends address and transfer direction
115
116 @param addr address and transfer direction of I2C device
117 @retval 0 device accessible
118 @retval 1 failed to access device
119 */
120extern unsigned char i2c_start(unsigned char addr);
121
122
123/**
124 @brief Issues a repeated start condition and sends address and transfer direction
125
126 @param addr address and transfer direction of I2C device
127 @retval 0 device accessible
128 @retval 1 failed to access device
129 */
130extern unsigned char i2c_rep_start(unsigned char addr);
131
132
133/**
134 @brief Issues a start condition and sends address and transfer direction
135
136 If device is busy, use ack polling to wait until device ready
137 @param addr address and transfer direction of I2C device
138 @return none
139 */
140extern void i2c_start_wait(unsigned char addr);
141
142
143/**
144 @brief Send one byte to I2C device
145 @param data byte to be transfered
146 @retval 0 write successful
147 @retval 1 write failed
148 */
149extern unsigned char i2c_write(unsigned char data);
150
151
152/**
153 @brief read one byte from the I2C device, request more data from device
154 @return byte read from I2C device
155 */
156extern unsigned char i2c_readAck(void);
157
158/**
159 @brief read one byte from the I2C device, read is followed by a stop condition
160 @return byte read from I2C device
161 */
162extern unsigned char i2c_readNak(void);
163
164/**
165 @brief read one byte from the I2C device
166
167 Implemented as a macro, which calls either i2c_readAck or i2c_readNak
168
169 @param ack 1 send ack, request more data from device<br>
170 0 send nak, read is followed by a stop condition
171 @return byte read from I2C device
172 */
173extern unsigned char i2c_read(unsigned char ack);
174#define i2c_read(ack) (ack) ? i2c_readAck() : i2c_readNak();
175
176
177/**@}*/
178#endif
diff --git a/keyboards/ergodox_ez/twimaster.c b/keyboards/ergodox_ez/twimaster.c
deleted file mode 100644
index f91c08e6e..000000000
--- a/keyboards/ergodox_ez/twimaster.c
+++ /dev/null
@@ -1,208 +0,0 @@
1/*************************************************************************
2* Title: I2C master library using hardware TWI interface
3* Author: Peter Fleury <pfleury@gmx.ch> http://jump.to/fleury
4* File: $Id: twimaster.c,v 1.3 2005/07/02 11:14:21 Peter Exp $
5* Software: AVR-GCC 3.4.3 / avr-libc 1.2.3
6* Target: any AVR device with hardware TWI
7* Usage: API compatible with I2C Software Library i2cmaster.h
8**************************************************************************/
9#include <inttypes.h>
10#include <compat/twi.h>
11
12#include <i2cmaster.h>
13
14
15/* define CPU frequency in Mhz here if not defined in Makefile */
16#ifndef F_CPU
17#define F_CPU 16000000UL
18#endif
19
20/* I2C clock in Hz */
21#define SCL_CLOCK 400000L
22
23
24/*************************************************************************
25 Initialization of the I2C bus interface. Need to be called only once
26*************************************************************************/
27void i2c_init(void)
28{
29 /* initialize TWI clock
30 * minimal values in Bit Rate Register (TWBR) and minimal Prescaler
31 * bits in the TWI Status Register should give us maximal possible
32 * I2C bus speed - about 444 kHz
33 *
34 * for more details, see 20.5.2 in ATmega16/32 secification
35 */
36
37 TWSR = 0; /* no prescaler */
38 TWBR = 10; /* must be >= 10 for stable operation */
39
40}/* i2c_init */
41
42
43/*************************************************************************
44 Issues a start condition and sends address and transfer direction.
45 return 0 = device accessible, 1= failed to access device
46*************************************************************************/
47unsigned char i2c_start(unsigned char address)
48{
49 uint8_t twst;
50
51 // send START condition
52 TWCR = (1<<TWINT) | (1<<TWSTA) | (1<<TWEN);
53
54 // wait until transmission completed
55 while(!(TWCR & (1<<TWINT)));
56
57 // check value of TWI Status Register. Mask prescaler bits.
58 twst = TW_STATUS & 0xF8;
59 if ( (twst != TW_START) && (twst != TW_REP_START)) return 1;
60
61 // send device address
62 TWDR = address;
63 TWCR = (1<<TWINT) | (1<<TWEN);
64
65 // wail until transmission completed and ACK/NACK has been received
66 while(!(TWCR & (1<<TWINT)));
67
68 // check value of TWI Status Register. Mask prescaler bits.
69 twst = TW_STATUS & 0xF8;
70 if ( (twst != TW_MT_SLA_ACK) && (twst != TW_MR_SLA_ACK) ) return 1;
71
72 return 0;
73
74}/* i2c_start */
75
76
77/*************************************************************************
78 Issues a start condition and sends address and transfer direction.
79 If device is busy, use ack polling to wait until device is ready
80
81 Input: address and transfer direction of I2C device
82*************************************************************************/
83void i2c_start_wait(unsigned char address)
84{
85 uint8_t twst;
86
87
88 while ( 1 )
89 {
90 // send START condition
91 TWCR = (1<<TWINT) | (1<<TWSTA) | (1<<TWEN);
92
93 // wait until transmission completed
94 while(!(TWCR & (1<<TWINT)));
95
96 // check value of TWI Status Register. Mask prescaler bits.
97 twst = TW_STATUS & 0xF8;
98 if ( (twst != TW_START) && (twst != TW_REP_START)) continue;
99
100 // send device address
101 TWDR = address;
102 TWCR = (1<<TWINT) | (1<<TWEN);
103
104 // wail until transmission completed
105 while(!(TWCR & (1<<TWINT)));
106
107 // check value of TWI Status Register. Mask prescaler bits.
108 twst = TW_STATUS & 0xF8;
109 if ( (twst == TW_MT_SLA_NACK )||(twst ==TW_MR_DATA_NACK) )
110 {
111 /* device busy, send stop condition to terminate write operation */
112 TWCR = (1<<TWINT) | (1<<TWEN) | (1<<TWSTO);
113
114 // wait until stop condition is executed and bus released
115 while(TWCR & (1<<TWSTO));
116
117 continue;
118 }
119 //if( twst != TW_MT_SLA_ACK) return 1;
120 break;
121 }
122
123}/* i2c_start_wait */
124
125
126/*************************************************************************
127 Issues a repeated start condition and sends address and transfer direction
128
129 Input: address and transfer direction of I2C device
130
131 Return: 0 device accessible
132 1 failed to access device
133*************************************************************************/
134unsigned char i2c_rep_start(unsigned char address)
135{
136 return i2c_start( address );
137
138}/* i2c_rep_start */
139
140
141/*************************************************************************
142 Terminates the data transfer and releases the I2C bus
143*************************************************************************/
144void i2c_stop(void)
145{
146 /* send stop condition */
147 TWCR = (1<<TWINT) | (1<<TWEN) | (1<<TWSTO);
148
149 // wait until stop condition is executed and bus released
150 while(TWCR & (1<<TWSTO));
151
152}/* i2c_stop */
153
154
155/*************************************************************************
156 Send one byte to I2C device
157
158 Input: byte to be transfered
159 Return: 0 write successful
160 1 write failed
161*************************************************************************/
162unsigned char i2c_write( unsigned char data )
163{
164 uint8_t twst;
165
166 // send data to the previously addressed device
167 TWDR = data;
168 TWCR = (1<<TWINT) | (1<<TWEN);
169
170 // wait until transmission completed
171 while(!(TWCR & (1<<TWINT)));
172
173 // check value of TWI Status Register. Mask prescaler bits
174 twst = TW_STATUS & 0xF8;
175 if( twst != TW_MT_DATA_ACK) return 1;
176 return 0;
177
178}/* i2c_write */
179
180
181/*************************************************************************
182 Read one byte from the I2C device, request more data from device
183
184 Return: byte read from I2C device
185*************************************************************************/
186unsigned char i2c_readAck(void)
187{
188 TWCR = (1<<TWINT) | (1<<TWEN) | (1<<TWEA);
189 while(!(TWCR & (1<<TWINT)));
190
191 return TWDR;
192
193}/* i2c_readAck */
194
195
196/*************************************************************************
197 Read one byte from the I2C device, read is followed by a stop condition
198
199 Return: byte read from I2C device
200*************************************************************************/
201unsigned char i2c_readNak(void)
202{
203 TWCR = (1<<TWINT) | (1<<TWEN);
204 while(!(TWCR & (1<<TWINT)));
205
206 return TWDR;
207
208}/* i2c_readNak */
generated by cgit v1.2.3 (git 2.25.1) at 2025-11-19 01:38:09 +0000