15 files changed, 263 insertions, 86 deletions

diff --git a/platforms/avr/drivers/analog.c b/platforms/avr/drivers/analog.c
index 8d299ffdb..628835cce 100644
--- a/platforms/avr/drivers/analog.c
+++ b/platforms/avr/drivers/analog.c
@@ -23,29 +23,6 @@ static uint8_t aref = ADC_REF_POWER;
 
 void analogReference(uint8_t mode) { aref = mode & (_BV(REFS1) | _BV(REFS0)); }
 
-// Arduino compatible pin input
-int16_t analogRead(uint8_t pin) {
-#if defined(__AVR_ATmega32U4__)
-    // clang-format off
-    static const uint8_t PROGMEM pin_to_mux[] = {
-        //A0    A1    A2    A3    A4    A5
-        //F7    F6    F5    F4    F1    F0
-        0x07, 0x06, 0x05, 0x04, 0x01, 0x00,
-        //A6    A7    A8    A9   A10   A11
-        //D4    D7    B4    B5    B6    D6
-        0x20, 0x22, 0x23, 0x24, 0x25, 0x21
-    };
-    // clang-format on
-    if (pin >= 12) return 0;
-    return adc_read(pgm_read_byte(pin_to_mux + pin));
-#elif defined(__AVR_AT90USB646__) || defined(__AVR_AT90USB647__) || defined(__AVR_AT90USB1286__) || defined(__AVR_AT90USB1287__) || defined(__AVR_ATmega328P__) || defined(__AVR_ATmega328__)
-    if (pin >= 8) return 0;
-    return adc_read(pin);
-#else
-    return 0;
-#endif
-}
-
 int16_t analogReadPin(pin_t pin) { return adc_read(pinToMux(pin)); }
 
 uint8_t pinToMux(pin_t pin) {
diff --git a/platforms/avr/drivers/analog.h b/platforms/avr/drivers/analog.h
index 058882450..b3c05e197 100644
--- a/platforms/avr/drivers/analog.h
+++ b/platforms/avr/drivers/analog.h
@@ -23,7 +23,6 @@
 extern "C" {
 #endif
 void    analogReference(uint8_t mode);
-int16_t analogRead(uint8_t pin);
 
 int16_t analogReadPin(pin_t pin);
 uint8_t pinToMux(pin_t pin);
diff --git a/platforms/chibios/boards/QMK_PROTON_C/configs/config.h b/platforms/chibios/boards/QMK_PROTON_C/configs/config.h
index a73f0c0b4..fa1a73c35 100644
--- a/platforms/chibios/boards/QMK_PROTON_C/configs/config.h
+++ b/platforms/chibios/boards/QMK_PROTON_C/configs/config.h
@@ -18,3 +18,12 @@
 #ifndef EARLY_INIT_PERFORM_BOOTLOADER_JUMP
 #    define EARLY_INIT_PERFORM_BOOTLOADER_JUMP TRUE
 #endif
+
+#ifdef CONVERT_TO_PROTON_C
+#    ifndef I2C1_SDA_PIN
+#        define I2C1_SDA_PIN D1
+#    endif
+#    ifndef I2C1_SCL_PIN
+#        define I2C1_SCL_PIN D0
+#    endif
+#endif
diff --git a/platforms/chibios/boards/common/ld/STM32F401xC.ld b/platforms/chibios/boards/common/ld/STM32F401xC.ld
new file mode 100644
index 000000000..8fae66cec
--- /dev/null
+++ b/platforms/chibios/boards/common/ld/STM32F401xC.ld
@@ -0,0 +1,85 @@
+/*
+    ChibiOS - Copyright (C) 2006..2018 Giovanni Di Sirio
+
+    Licensed under the Apache License, Version 2.0 (the "License");
+    you may not use this file except in compliance with the License.
+    You may obtain a copy of the License at
+
+        http://www.apache.org/licenses/LICENSE-2.0
+
+    Unless required by applicable law or agreed to in writing, software
+    distributed under the License is distributed on an "AS IS" BASIS,
+    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+    See the License for the specific language governing permissions and
+    limitations under the License.
+*/
+
+/*
+ * STM32F401xC memory setup.
+ */
+MEMORY
+{
+    flash0 (rx) : org = 0x08000000, len = 16k        /* Sector 0    - Init code as ROM bootloader assumes application starts here */
+    flash1 (rx) : org = 0x08004000, len = 16k        /* Sector 1    - Emulated eeprom */
+    flash2 (rx) : org = 0x08008000, len = 256k - 32k /* Sector 2..6 - Rest of firmware */
+    flash3 (rx) : org = 0x00000000, len = 0
+    flash4 (rx) : org = 0x00000000, len = 0
+    flash5 (rx) : org = 0x00000000, len = 0
+    flash6 (rx) : org = 0x00000000, len = 0
+    flash7 (rx) : org = 0x00000000, len = 0
+    ram0   (wx) : org = 0x20000000, len = 64k
+    ram1   (wx) : org = 0x00000000, len = 0
+    ram2   (wx) : org = 0x00000000, len = 0
+    ram3   (wx) : org = 0x00000000, len = 0
+    ram4   (wx) : org = 0x00000000, len = 0
+    ram5   (wx) : org = 0x00000000, len = 0
+    ram6   (wx) : org = 0x00000000, len = 0
+    ram7   (wx) : org = 0x00000000, len = 0
+}
+
+/* For each data/text section two region are defined, a virtual region
+   and a load region (_LMA suffix).*/
+
+/* Flash region to be used for exception vectors.*/
+REGION_ALIAS("VECTORS_FLASH", flash0);
+REGION_ALIAS("VECTORS_FLASH_LMA", flash0);
+
+/* Flash region to be used for constructors and destructors.*/
+REGION_ALIAS("XTORS_FLASH", flash2);
+REGION_ALIAS("XTORS_FLASH_LMA", flash2);
+
+/* Flash region to be used for code text.*/
+REGION_ALIAS("TEXT_FLASH", flash2);
+REGION_ALIAS("TEXT_FLASH_LMA", flash2);
+
+/* Flash region to be used for read only data.*/
+REGION_ALIAS("RODATA_FLASH", flash2);
+REGION_ALIAS("RODATA_FLASH_LMA", flash2);
+
+/* Flash region to be used for various.*/
+REGION_ALIAS("VARIOUS_FLASH", flash2);
+REGION_ALIAS("VARIOUS_FLASH_LMA", flash2);
+
+/* Flash region to be used for RAM(n) initialization data.*/
+REGION_ALIAS("RAM_INIT_FLASH_LMA", flash2);
+
+/* RAM region to be used for Main stack. This stack accommodates the processing
+   of all exceptions and interrupts.*/
+REGION_ALIAS("MAIN_STACK_RAM", ram0);
+
+/* RAM region to be used for the process stack. This is the stack used by
+   the main() function.*/
+REGION_ALIAS("PROCESS_STACK_RAM", ram0);
+
+/* RAM region to be used for data segment.*/
+REGION_ALIAS("DATA_RAM", ram0);
+REGION_ALIAS("DATA_RAM_LMA", flash2);
+
+/* RAM region to be used for BSS segment.*/
+REGION_ALIAS("BSS_RAM", ram0);
+
+/* RAM region to be used for the default heap.*/
+REGION_ALIAS("HEAP_RAM", ram0);
+
+/* Generic rules inclusion.*/
+INCLUDE rules.ld
diff --git a/platforms/chibios/boards/common/ld/STM32F411xE.ld b/platforms/chibios/boards/common/ld/STM32F411xE.ld
new file mode 100644
index 000000000..aea8084b5
--- /dev/null
+++ b/platforms/chibios/boards/common/ld/STM32F411xE.ld
@@ -0,0 +1,85 @@
+/*
+    ChibiOS - Copyright (C) 2006..2018 Giovanni Di Sirio
+
+    Licensed under the Apache License, Version 2.0 (the "License");
+    you may not use this file except in compliance with the License.
+    You may obtain a copy of the License at
+
+        http://www.apache.org/licenses/LICENSE-2.0
+
+    Unless required by applicable law or agreed to in writing, software
+    distributed under the License is distributed on an "AS IS" BASIS,
+    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+    See the License for the specific language governing permissions and
+    limitations under the License.
+*/
+
+/*
+ * STM32F411xE memory setup.
+ */
+MEMORY
+{
+    flash0 (rx) : org = 0x08000000, len = 16k        /* Sector 0    - Init code as ROM bootloader assumes application starts here */
+    flash1 (rx) : org = 0x08004000, len = 16k        /* Sector 1    - Emulated eeprom */
+    flash2 (rx) : org = 0x08008000, len = 512k - 32k /* Sector 2..7 - Rest of firmware */
+    flash3 (rx) : org = 0x00000000, len = 0
+    flash4 (rx) : org = 0x00000000, len = 0
+    flash5 (rx) : org = 0x00000000, len = 0
+    flash6 (rx) : org = 0x00000000, len = 0
+    flash7 (rx) : org = 0x00000000, len = 0
+    ram0   (wx) : org = 0x20000000, len = 128k
+    ram1   (wx) : org = 0x00000000, len = 0
+    ram2   (wx) : org = 0x00000000, len = 0
+    ram3   (wx) : org = 0x00000000, len = 0
+    ram4   (wx) : org = 0x00000000, len = 0
+    ram5   (wx) : org = 0x00000000, len = 0
+    ram6   (wx) : org = 0x00000000, len = 0
+    ram7   (wx) : org = 0x00000000, len = 0
+}
+
+/* For each data/text section two region are defined, a virtual region
+   and a load region (_LMA suffix).*/
+
+/* Flash region to be used for exception vectors.*/
+REGION_ALIAS("VECTORS_FLASH", flash0);
+REGION_ALIAS("VECTORS_FLASH_LMA", flash0);
+
+/* Flash region to be used for constructors and destructors.*/
+REGION_ALIAS("XTORS_FLASH", flash2);
+REGION_ALIAS("XTORS_FLASH_LMA", flash2);
+
+/* Flash region to be used for code text.*/
+REGION_ALIAS("TEXT_FLASH", flash2);
+REGION_ALIAS("TEXT_FLASH_LMA", flash2);
+
+/* Flash region to be used for read only data.*/
+REGION_ALIAS("RODATA_FLASH", flash2);
+REGION_ALIAS("RODATA_FLASH_LMA", flash2);
+
+/* Flash region to be used for various.*/
+REGION_ALIAS("VARIOUS_FLASH", flash2);
+REGION_ALIAS("VARIOUS_FLASH_LMA", flash2);
+
+/* Flash region to be used for RAM(n) initialization data.*/
+REGION_ALIAS("RAM_INIT_FLASH_LMA", flash2);
+
+/* RAM region to be used for Main stack. This stack accommodates the processing
+   of all exceptions and interrupts.*/
+REGION_ALIAS("MAIN_STACK_RAM", ram0);
+
+/* RAM region to be used for the process stack. This is the stack used by
+   the main() function.*/
+REGION_ALIAS("PROCESS_STACK_RAM", ram0);
+
+/* RAM region to be used for data segment.*/
+REGION_ALIAS("DATA_RAM", ram0);
+REGION_ALIAS("DATA_RAM_LMA", flash2);
+
+/* RAM region to be used for BSS segment.*/
+REGION_ALIAS("BSS_RAM", ram0);
+
+/* RAM region to be used for the default heap.*/
+REGION_ALIAS("HEAP_RAM", ram0);
+
+/* Generic rules inclusion.*/
+INCLUDE rules.ld
diff --git a/platforms/chibios/drivers/i2c_master.c b/platforms/chibios/drivers/i2c_master.c
index fc4bb2ab3..981f6fa06 100644
--- a/platforms/chibios/drivers/i2c_master.c
+++ b/platforms/chibios/drivers/i2c_master.c
@@ -63,16 +63,16 @@ __attribute__((weak)) void i2c_init(void) {
         is_initialised = true;
 
         // Try releasing special pins for a short time
-        palSetPadMode(I2C1_SCL_BANK, I2C1_SCL, PAL_MODE_INPUT);
-        palSetPadMode(I2C1_SDA_BANK, I2C1_SDA, PAL_MODE_INPUT);
+        palSetLineMode(I2C1_SCL_PIN, PAL_MODE_INPUT);
+        palSetLineMode(I2C1_SDA_PIN, PAL_MODE_INPUT);
 
         chThdSleepMilliseconds(10);
 #if defined(USE_GPIOV1)
-        palSetPadMode(I2C1_SCL_BANK, I2C1_SCL, I2C1_SCL_PAL_MODE);
-        palSetPadMode(I2C1_SDA_BANK, I2C1_SDA, I2C1_SDA_PAL_MODE);
+        palSetLineMode(I2C1_SCL_PIN, I2C1_SCL_PAL_MODE);
+        palSetLineMode(I2C1_SDA_PIN, I2C1_SDA_PAL_MODE);
 #else
-        palSetPadMode(I2C1_SCL_BANK, I2C1_SCL, PAL_MODE_ALTERNATE(I2C1_SCL_PAL_MODE) | PAL_STM32_OTYPE_OPENDRAIN);
-        palSetPadMode(I2C1_SDA_BANK, I2C1_SDA, PAL_MODE_ALTERNATE(I2C1_SDA_PAL_MODE) | PAL_STM32_OTYPE_OPENDRAIN);
+        palSetLineMode(I2C1_SCL_PIN, PAL_MODE_ALTERNATE(I2C1_SCL_PAL_MODE) | PAL_OUTPUT_TYPE_OPENDRAIN);
+        palSetLineMode(I2C1_SDA_PIN, PAL_MODE_ALTERNATE(I2C1_SDA_PAL_MODE) | PAL_OUTPUT_TYPE_OPENDRAIN);
 #endif
     }
 }
diff --git a/platforms/chibios/drivers/i2c_master.h b/platforms/chibios/drivers/i2c_master.h
index c68109acb..ce32fd245 100644
--- a/platforms/chibios/drivers/i2c_master.h
+++ b/platforms/chibios/drivers/i2c_master.h
@@ -27,24 +27,11 @@
 #include <ch.h>
 #include <hal.h>
 
-#ifdef I2C1_BANK
-#    define I2C1_SCL_BANK I2C1_BANK
-#    define I2C1_SDA_BANK I2C1_BANK
+#ifndef I2C1_SCL_PIN
+#    define I2C1_SCL_PIN B6
 #endif
-
-#ifndef I2C1_SCL_BANK
-#    define I2C1_SCL_BANK GPIOB
-#endif
-
-#ifndef I2C1_SDA_BANK
-#    define I2C1_SDA_BANK GPIOB
-#endif
-
-#ifndef I2C1_SCL
-#    define I2C1_SCL 6
-#endif
-#ifndef I2C1_SDA
-#    define I2C1_SDA 7
+#ifndef I2C1_SDA_PIN
+#    define I2C1_SDA_PIN B7
 #endif
 
 #ifdef USE_I2CV1
@@ -83,10 +70,10 @@
 
 #ifdef USE_GPIOV1
 #    ifndef I2C1_SCL_PAL_MODE
-#        define I2C1_SCL_PAL_MODE PAL_MODE_STM32_ALTERNATE_OPENDRAIN
+#        define I2C1_SCL_PAL_MODE PAL_MODE_ALTERNATE_OPENDRAIN
 #    endif
 #    ifndef I2C1_SDA_PAL_MODE
-#        define I2C1_SDA_PAL_MODE PAL_MODE_STM32_ALTERNATE_OPENDRAIN
+#        define I2C1_SDA_PAL_MODE PAL_MODE_ALTERNATE_OPENDRAIN
 #    endif
 #else
 // The default PAL alternate modes are used to signal that the pins are used for I2C
diff --git a/platforms/chibios/drivers/serial.c b/platforms/chibios/drivers/serial.c
index f54fbcee4..ef6f0aa8d 100644
--- a/platforms/chibios/drivers/serial.c
+++ b/platforms/chibios/drivers/serial.c
@@ -19,7 +19,7 @@
 #    error "chSysPolledDelayX method not supported on this platform"
 #else
 #    undef wait_us
-#    define wait_us(x) chSysPolledDelayX(US2RTC(STM32_SYSCLK, x))
+#    define wait_us(x) chSysPolledDelayX(US2RTC(CPU_CLOCK, x))
 #endif
 
 #ifndef SELECT_SOFT_SERIAL_SPEED
diff --git a/platforms/chibios/drivers/serial_usart.c b/platforms/chibios/drivers/serial_usart.c
index ea4473791..124e4be68 100644
--- a/platforms/chibios/drivers/serial_usart.c
+++ b/platforms/chibios/drivers/serial_usart.c
@@ -104,9 +104,9 @@ static inline bool receive(uint8_t* destination, const size_t size) {
 __attribute__((weak)) void usart_init(void) {
 #    if defined(MCU_STM32)
 #        if defined(USE_GPIOV1)
-    palSetLineMode(SERIAL_USART_TX_PIN, PAL_MODE_STM32_ALTERNATE_OPENDRAIN);
+    palSetLineMode(SERIAL_USART_TX_PIN, PAL_MODE_ALTERNATE_OPENDRAIN);
 #        else
-    palSetLineMode(SERIAL_USART_TX_PIN, PAL_MODE_ALTERNATE(SERIAL_USART_TX_PAL_MODE) | PAL_STM32_OTYPE_OPENDRAIN);
+    palSetLineMode(SERIAL_USART_TX_PIN, PAL_MODE_ALTERNATE(SERIAL_USART_TX_PAL_MODE) | PAL_OUTPUT_TYPE_OPENDRAIN);
 #        endif
 
 #        if defined(USART_REMAP)
@@ -125,11 +125,11 @@ __attribute__((weak)) void usart_init(void) {
 __attribute__((weak)) void usart_init(void) {
 #    if defined(MCU_STM32)
 #        if defined(USE_GPIOV1)
-    palSetLineMode(SERIAL_USART_TX_PIN, PAL_MODE_STM32_ALTERNATE_PUSHPULL);
+    palSetLineMode(SERIAL_USART_TX_PIN, PAL_MODE_ALTERNATE_PUSHPULL);
     palSetLineMode(SERIAL_USART_RX_PIN, PAL_MODE_INPUT);
 #        else
-    palSetLineMode(SERIAL_USART_TX_PIN, PAL_MODE_ALTERNATE(SERIAL_USART_TX_PAL_MODE) | PAL_STM32_OTYPE_PUSHPULL | PAL_STM32_OSPEED_HIGHEST);
-    palSetLineMode(SERIAL_USART_RX_PIN, PAL_MODE_ALTERNATE(SERIAL_USART_RX_PAL_MODE) | PAL_STM32_OTYPE_PUSHPULL | PAL_STM32_OSPEED_HIGHEST);
+    palSetLineMode(SERIAL_USART_TX_PIN, PAL_MODE_ALTERNATE(SERIAL_USART_TX_PAL_MODE) | PAL_OUTPUT_TYPE_PUSHPULL | PAL_OUTPUT_SPEED_HIGHEST);
+    palSetLineMode(SERIAL_USART_RX_PIN, PAL_MODE_ALTERNATE(SERIAL_USART_RX_PAL_MODE) | PAL_OUTPUT_TYPE_PUSHPULL | PAL_OUTPUT_SPEED_HIGHEST);
 #        endif
 
 #        if defined(USART_REMAP)
diff --git a/platforms/chibios/drivers/spi_master.c b/platforms/chibios/drivers/spi_master.c
index 28ddcbb2b..f98db6db9 100644
--- a/platforms/chibios/drivers/spi_master.c
+++ b/platforms/chibios/drivers/spi_master.c
@@ -42,9 +42,9 @@ __attribute__((weak)) void spi_init(void) {
         palSetPadMode(PAL_PORT(SPI_MOSI_PIN), PAL_PAD(SPI_MOSI_PIN), SPI_MOSI_PAL_MODE);
         palSetPadMode(PAL_PORT(SPI_MISO_PIN), PAL_PAD(SPI_MISO_PIN), SPI_MISO_PAL_MODE);
 #else
-        palSetPadMode(PAL_PORT(SPI_SCK_PIN), PAL_PAD(SPI_SCK_PIN), PAL_MODE_ALTERNATE(SPI_SCK_PAL_MODE) | PAL_STM32_OTYPE_PUSHPULL | PAL_STM32_OSPEED_HIGHEST);
-        palSetPadMode(PAL_PORT(SPI_MOSI_PIN), PAL_PAD(SPI_MOSI_PIN), PAL_MODE_ALTERNATE(SPI_MOSI_PAL_MODE) | PAL_STM32_OTYPE_PUSHPULL | PAL_STM32_OSPEED_HIGHEST);
-        palSetPadMode(PAL_PORT(SPI_MISO_PIN), PAL_PAD(SPI_MISO_PIN), PAL_MODE_ALTERNATE(SPI_MISO_PAL_MODE) | PAL_STM32_OTYPE_PUSHPULL | PAL_STM32_OSPEED_HIGHEST);
+        palSetPadMode(PAL_PORT(SPI_SCK_PIN), PAL_PAD(SPI_SCK_PIN), PAL_MODE_ALTERNATE(SPI_SCK_PAL_MODE) | PAL_OUTPUT_TYPE_PUSHPULL | PAL_OUTPUT_SPEED_HIGHEST);
+        palSetPadMode(PAL_PORT(SPI_MOSI_PIN), PAL_PAD(SPI_MOSI_PIN), PAL_MODE_ALTERNATE(SPI_MOSI_PAL_MODE) | PAL_OUTPUT_TYPE_PUSHPULL | PAL_OUTPUT_SPEED_HIGHEST);
+        palSetPadMode(PAL_PORT(SPI_MISO_PIN), PAL_PAD(SPI_MISO_PIN), PAL_MODE_ALTERNATE(SPI_MISO_PAL_MODE) | PAL_OUTPUT_TYPE_PUSHPULL | PAL_OUTPUT_SPEED_HIGHEST);
 #endif
     }
 }
diff --git a/platforms/chibios/drivers/spi_master.h b/platforms/chibios/drivers/spi_master.h
index b5a6ef143..6a3ce481f 100644
--- a/platforms/chibios/drivers/spi_master.h
+++ b/platforms/chibios/drivers/spi_master.h
@@ -33,7 +33,7 @@
 
 #ifndef SPI_SCK_PAL_MODE
 #    if defined(USE_GPIOV1)
-#        define SPI_SCK_PAL_MODE PAL_MODE_STM32_ALTERNATE_PUSHPULL
+#        define SPI_SCK_PAL_MODE PAL_MODE_ALTERNATE_PUSHPULL
 #    else
 #        define SPI_SCK_PAL_MODE 5
 #    endif
@@ -45,7 +45,7 @@
 
 #ifndef SPI_MOSI_PAL_MODE
 #    if defined(USE_GPIOV1)
-#        define SPI_MOSI_PAL_MODE PAL_MODE_STM32_ALTERNATE_PUSHPULL
+#        define SPI_MOSI_PAL_MODE PAL_MODE_ALTERNATE_PUSHPULL
 #    else
 #        define SPI_MOSI_PAL_MODE 5
 #    endif
@@ -57,7 +57,7 @@
 
 #ifndef SPI_MISO_PAL_MODE
 #    if defined(USE_GPIOV1)
-#        define SPI_MISO_PAL_MODE PAL_MODE_STM32_ALTERNATE_PUSHPULL
+#        define SPI_MISO_PAL_MODE PAL_MODE_ALTERNATE_PUSHPULL
 #    else
 #        define SPI_MISO_PAL_MODE 5
 #    endif
diff --git a/platforms/chibios/drivers/uart.c b/platforms/chibios/drivers/uart.c
index 030335b34..0e8e0515a 100644
--- a/platforms/chibios/drivers/uart.c
+++ b/platforms/chibios/drivers/uart.c
@@ -29,11 +29,11 @@ void uart_init(uint32_t baud) {
         serialConfig.speed = baud;
 
 #if defined(USE_GPIOV1)
-        palSetLineMode(SD1_TX_PIN, PAL_MODE_STM32_ALTERNATE_OPENDRAIN);
-        palSetLineMode(SD1_RX_PIN, PAL_MODE_STM32_ALTERNATE_OPENDRAIN);
+        palSetLineMode(SD1_TX_PIN, PAL_MODE_ALTERNATE_OPENDRAIN);
+        palSetLineMode(SD1_RX_PIN, PAL_MODE_ALTERNATE_OPENDRAIN);
 #else
-        palSetLineMode(SD1_TX_PIN, PAL_MODE_ALTERNATE(SD1_TX_PAL_MODE) | PAL_STM32_OTYPE_OPENDRAIN);
-        palSetLineMode(SD1_RX_PIN, PAL_MODE_ALTERNATE(SD1_RX_PAL_MODE) | PAL_STM32_OTYPE_OPENDRAIN);
+        palSetLineMode(SD1_TX_PIN, PAL_MODE_ALTERNATE(SD1_TX_PAL_MODE) | PAL_OUTPUT_TYPE_OPENDRAIN);
+        palSetLineMode(SD1_RX_PIN, PAL_MODE_ALTERNATE(SD1_RX_PAL_MODE) | PAL_OUTPUT_TYPE_OPENDRAIN);
 #endif
         sdStart(&SERIAL_DRIVER, &serialConfig);
     }
diff --git a/platforms/chibios/drivers/ws2812.c b/platforms/chibios/drivers/ws2812.c
index 0d12e2fb7..ffcdcff24 100644
--- a/platforms/chibios/drivers/ws2812.c
+++ b/platforms/chibios/drivers/ws2812.c
@@ -23,7 +23,7 @@
 #endif
 
 #define NUMBER_NOPS 6
-#define CYCLES_PER_SEC (STM32_SYSCLK / NUMBER_NOPS * NOP_FUDGE)
+#define CYCLES_PER_SEC (CPU_CLOCK / NUMBER_NOPS * NOP_FUDGE)
 #define NS_PER_SEC (1000000000L)  // Note that this has to be SIGNED since we want to be able to check for negative values of derivatives
 #define NS_PER_CYCLE (NS_PER_SEC / CYCLES_PER_SEC)
 #define NS_TO_CYCLES(n) ((n) / NS_PER_CYCLE)
diff --git a/platforms/chibios/drivers/ws2812_pwm.c b/platforms/chibios/drivers/ws2812_pwm.c
index e6af55b6b..c17b9cd4e 100644
--- a/platforms/chibios/drivers/ws2812_pwm.c
+++ b/platforms/chibios/drivers/ws2812_pwm.c
@@ -5,7 +5,9 @@
 /* Adapted from https://github.com/joewa/WS2812-LED-Driver_ChibiOS/ */
 
 #ifdef RGBW
-#    error "RGBW not supported"
+#    define WS2812_CHANNELS 4
+#else
+#    define WS2812_CHANNELS 3
 #endif
 
 #ifndef WS2812_PWM_DRIVER
@@ -40,15 +42,15 @@
 // Default Push Pull
 #ifndef WS2812_EXTERNAL_PULLUP
 #    if defined(USE_GPIOV1)
-#        define WS2812_OUTPUT_MODE PAL_MODE_STM32_ALTERNATE_PUSHPULL
+#        define WS2812_OUTPUT_MODE PAL_MODE_ALTERNATE_PUSHPULL
 #    else
-#        define WS2812_OUTPUT_MODE PAL_MODE_ALTERNATE(WS2812_PWM_PAL_MODE) | PAL_STM32_OTYPE_PUSHPULL | PAL_STM32_OSPEED_HIGHEST | PAL_STM32_PUPDR_FLOATING
+#        define WS2812_OUTPUT_MODE PAL_MODE_ALTERNATE(WS2812_PWM_PAL_MODE) | PAL_OUTPUT_TYPE_PUSHPULL | PAL_OUTPUT_SPEED_HIGHEST | PAL_PUPDR_FLOATING
 #    endif
 #else
 #    if defined(USE_GPIOV1)
-#        define WS2812_OUTPUT_MODE PAL_MODE_STM32_ALTERNATE_OPENDRAIN
+#        define WS2812_OUTPUT_MODE PAL_MODE_ALTERNATE_OPENDRAIN
 #    else
-#        define WS2812_OUTPUT_MODE PAL_MODE_ALTERNATE(WS2812_PWM_PAL_MODE) | PAL_STM32_OTYPE_OPENDRAIN | PAL_STM32_OSPEED_HIGHEST | PAL_STM32_PUPDR_FLOATING
+#        define WS2812_OUTPUT_MODE PAL_MODE_ALTERNATE(WS2812_PWM_PAL_MODE) | PAL_OUTPUT_TYPE_OPENDRAIN | PAL_OUTPUT_SPEED_HIGHEST | PAL_PUPDR_FLOATING
 #    endif
 #endif
 
@@ -59,7 +61,7 @@
 
 /* --- PRIVATE CONSTANTS ---------------------------------------------------- */
 
-#define WS2812_PWM_FREQUENCY (STM32_SYSCLK / 2)                             /**< Clock frequency of PWM, must be valid with respect to system clock! */
+#define WS2812_PWM_FREQUENCY (CPU_CLOCK / 2)                                /**< Clock frequency of PWM, must be valid with respect to system clock! */
 #define WS2812_PWM_PERIOD (WS2812_PWM_FREQUENCY / WS2812_PWM_TARGET_PERIOD) /**< Clock period in ticks. 1 / 800kHz = 1.25 uS (as per datasheet) */
 
 /**
@@ -68,8 +70,9 @@
  * The reset period for each frame is defined in WS2812_TRST_US.
  * Calculate the number of zeroes to add at the end assuming 1.25 uS/bit:
  */
+#define WS2812_COLOR_BITS (WS2812_CHANNELS * 8)
 #define WS2812_RESET_BIT_N (1000 * WS2812_TRST_US / 1250)
-#define WS2812_COLOR_BIT_N (RGBLED_NUM * 24)                   /**< Number of data bits */
+#define WS2812_COLOR_BIT_N (RGBLED_NUM * WS2812_COLOR_BITS)    /**< Number of data bits */
 #define WS2812_BIT_N (WS2812_COLOR_BIT_N + WS2812_RESET_BIT_N) /**< Total number of bits in a frame */
 
 /**
@@ -114,7 +117,7 @@
  *
  * @return                          The bit index
  */
-#define WS2812_BIT(led, byte, bit) (24 * (led) + 8 * (byte) + (7 - (bit)))
+#define WS2812_BIT(led, byte, bit) (WS2812_COLOR_BITS * (led) + 8 * (byte) + (7 - (bit)))
 
 #if (WS2812_BYTE_ORDER == WS2812_BYTE_ORDER_GRB)
 /**
@@ -228,6 +231,20 @@
 #    define WS2812_BLUE_BIT(led, bit) WS2812_BIT((led), 0, (bit))
 #endif
 
+#ifdef RGBW
+/**
+ * @brief   Determine the index in @ref ws2812_frame_buffer "the frame buffer" of a given white bit
+ *
+ * @note    The white byte is the last byte in the color packet
+ *
+ * @param[in] led:                  The led index [0, @ref WS2812_LED_N)
+ * @param[in] bit:                  The bit index [0, 7]
+ *
+ * @return                          The bit index
+ */
+#    define WS2812_WHITE_BIT(led, bit) WS2812_BIT((led), 3, (bit))
+#endif
+
 /* --- PRIVATE VARIABLES ---------------------------------------------------- */
 
 static uint32_t ws2812_frame_buffer[WS2812_BIT_N + 1]; /**< Buffer for a frame */
@@ -296,6 +313,17 @@ void ws2812_write_led(uint16_t led_number, uint8_t r, uint8_t g, uint8_t b) {
         ws2812_frame_buffer[WS2812_BLUE_BIT(led_number, bit)]  = ((b >> bit) & 0x01) ? WS2812_DUTYCYCLE_1 : WS2812_DUTYCYCLE_0;
     }
 }
+void ws2812_write_led_rgbw(uint16_t led_number, uint8_t r, uint8_t g, uint8_t b, uint8_t w) {
+    // Write color to frame buffer
+    for (uint8_t bit = 0; bit < 8; bit++) {
+        ws2812_frame_buffer[WS2812_RED_BIT(led_number, bit)]   = ((r >> bit) & 0x01) ? WS2812_DUTYCYCLE_1 : WS2812_DUTYCYCLE_0;
+        ws2812_frame_buffer[WS2812_GREEN_BIT(led_number, bit)] = ((g >> bit) & 0x01) ? WS2812_DUTYCYCLE_1 : WS2812_DUTYCYCLE_0;
+        ws2812_frame_buffer[WS2812_BLUE_BIT(led_number, bit)]  = ((b >> bit) & 0x01) ? WS2812_DUTYCYCLE_1 : WS2812_DUTYCYCLE_0;
+#ifdef RGBW
+        ws2812_frame_buffer[WS2812_WHITE_BIT(led_number, bit)] = ((w >> bit) & 0x01) ? WS2812_DUTYCYCLE_1 : WS2812_DUTYCYCLE_0;
+#endif
+    }
+}
 
 // Setleds for standard RGB
 void ws2812_setleds(LED_TYPE* ledarray, uint16_t leds) {
@@ -306,6 +334,10 @@ void ws2812_setleds(LED_TYPE* ledarray, uint16_t leds) {
     }
 
     for (uint16_t i = 0; i < leds; i++) {
+#ifdef RGBW
+        ws2812_write_led_rgbw(i, ledarray[i].r, ledarray[i].g, ledarray[i].b, ledarray[i].w);
+#else
         ws2812_write_led(i, ledarray[i].r, ledarray[i].g, ledarray[i].b);
+#endif
     }
 }
diff --git a/platforms/chibios/drivers/ws2812_spi.c b/platforms/chibios/drivers/ws2812_spi.c
index fe14b478a..62722f466 100644
--- a/platforms/chibios/drivers/ws2812_spi.c
+++ b/platforms/chibios/drivers/ws2812_spi.c
@@ -3,10 +3,6 @@
 
 /* Adapted from https://github.com/gamazeps/ws2812b-chibios-SPIDMA/ */
 
-#ifdef RGBW
-#    error "RGBW not supported"
-#endif
-
 // Define the spi your LEDs are plugged to here
 #ifndef WS2812_SPI
 #    define WS2812_SPI SPID1
@@ -24,15 +20,15 @@
 // Default Push Pull
 #ifndef WS2812_EXTERNAL_PULLUP
 #    if defined(USE_GPIOV1)
-#        define WS2812_MOSI_OUTPUT_MODE PAL_MODE_STM32_ALTERNATE_PUSHPULL
+#        define WS2812_MOSI_OUTPUT_MODE PAL_MODE_ALTERNATE_PUSHPULL
 #    else
-#        define WS2812_MOSI_OUTPUT_MODE PAL_MODE_ALTERNATE(WS2812_SPI_MOSI_PAL_MODE) | PAL_STM32_OTYPE_PUSHPULL
+#        define WS2812_MOSI_OUTPUT_MODE PAL_MODE_ALTERNATE(WS2812_SPI_MOSI_PAL_MODE) | PAL_OUTPUT_TYPE_PUSHPULL
 #    endif
 #else
 #    if defined(USE_GPIOV1)
-#        define WS2812_MOSI_OUTPUT_MODE PAL_MODE_STM32_ALTERNATE_OPENDRAIN
+#        define WS2812_MOSI_OUTPUT_MODE PAL_MODE_ALTERNATE_OPENDRAIN
 #    else
-#        define WS2812_MOSI_OUTPUT_MODE PAL_MODE_ALTERNATE(WS2812_SPI_MOSI_PAL_MODE) | PAL_STM32_OTYPE_OPENDRAIN
+#        define WS2812_MOSI_OUTPUT_MODE PAL_MODE_ALTERNATE(WS2812_SPI_MOSI_PAL_MODE) | PAL_OUTPUT_TYPE_OPENDRAIN
 #    endif
 #endif
 
@@ -68,14 +64,18 @@
 #endif
 
 #if defined(USE_GPIOV1)
-#    define WS2812_SCK_OUTPUT_MODE PAL_MODE_STM32_ALTERNATE_PUSHPULL
+#    define WS2812_SCK_OUTPUT_MODE PAL_MODE_ALTERNATE_PUSHPULL
 #else
-#    define WS2812_SCK_OUTPUT_MODE PAL_MODE_ALTERNATE(WS2812_SPI_SCK_PAL_MODE) | PAL_STM32_OTYPE_PUSHPULL
+#    define WS2812_SCK_OUTPUT_MODE PAL_MODE_ALTERNATE(WS2812_SPI_SCK_PAL_MODE) | PAL_OUTPUT_TYPE_PUSHPULL
 #endif
 
 #define BYTES_FOR_LED_BYTE 4
-#define NB_COLORS 3
-#define BYTES_FOR_LED (BYTES_FOR_LED_BYTE * NB_COLORS)
+#ifdef RGBW
+#    define WS2812_CHANNELS 4
+#else
+#    define WS2812_CHANNELS 3
+#endif
+#define BYTES_FOR_LED (BYTES_FOR_LED_BYTE * WS2812_CHANNELS)
 #define DATA_SIZE (BYTES_FOR_LED * RGBLED_NUM)
 #define RESET_SIZE (1000 * WS2812_TRST_US / (2 * 1250))
 #define PREAMBLE_SIZE 4
@@ -116,6 +116,9 @@ static void set_led_color_rgb(LED_TYPE color, int pos) {
     for (int j = 0; j < 4; j++) tx_start[BYTES_FOR_LED * pos + BYTES_FOR_LED_BYTE + j] = get_protocol_eq(color.g, j);
     for (int j = 0; j < 4; j++) tx_start[BYTES_FOR_LED * pos + BYTES_FOR_LED_BYTE * 2 + j] = get_protocol_eq(color.r, j);
 #endif
+#ifdef RGBW
+    for (int j = 0; j < 4; j++) tx_start[BYTES_FOR_LED * pos + BYTES_FOR_LED_BYTE * 4 + j] = get_protocol_eq(color.w, j);
+#endif
 }
 
 void ws2812_init(void) {