aboutsummaryrefslogtreecommitdiff
path: root/keyboards/zinc/serial.c
diff options
context:
space:
mode:
Diffstat (limited to 'keyboards/zinc/serial.c')
-rw-r--r--keyboards/zinc/serial.c589
1 files changed, 0 insertions, 589 deletions
diff --git a/keyboards/zinc/serial.c b/keyboards/zinc/serial.c
deleted file mode 100644
index f6293c3dc..000000000
--- a/keyboards/zinc/serial.c
+++ /dev/null
@@ -1,589 +0,0 @@
1/*
2 * WARNING: be careful changing this code, it is very timing dependent
3 *
4 * 2018-10-28 checked
5 * avr-gcc 4.9.2
6 * avr-gcc 5.4.0
7 * avr-gcc 7.3.0
8 */
9
10#ifndef F_CPU
11#define F_CPU 16000000
12#endif
13
14#include <avr/io.h>
15#include <avr/interrupt.h>
16#include <util/delay.h>
17#include <stddef.h>
18#include <stdbool.h>
19#include "serial.h"
20
21#ifdef SOFT_SERIAL_PIN
22
23#ifdef __AVR_ATmega32U4__
24 // if using ATmega32U4 I2C, can not use PD0 and PD1 in soft serial.
25 #ifdef USE_I2C
26 #if SOFT_SERIAL_PIN == D0 || SOFT_SERIAL_PIN == D1
27 #error Using ATmega32U4 I2C, so can not use PD0, PD1
28 #endif
29 #endif
30
31 #if SOFT_SERIAL_PIN >= D0 && SOFT_SERIAL_PIN <= D3
32 #define SERIAL_PIN_DDR DDRD
33 #define SERIAL_PIN_PORT PORTD
34 #define SERIAL_PIN_INPUT PIND
35 #if SOFT_SERIAL_PIN == D0
36 #define SERIAL_PIN_MASK _BV(PD0)
37 #define EIMSK_BIT _BV(INT0)
38 #define EICRx_BIT (~(_BV(ISC00) | _BV(ISC01)))
39 #define SERIAL_PIN_INTERRUPT INT0_vect
40 #elif SOFT_SERIAL_PIN == D1
41 #define SERIAL_PIN_MASK _BV(PD1)
42 #define EIMSK_BIT _BV(INT1)
43 #define EICRx_BIT (~(_BV(ISC10) | _BV(ISC11)))
44 #define SERIAL_PIN_INTERRUPT INT1_vect
45 #elif SOFT_SERIAL_PIN == D2
46 #define SERIAL_PIN_MASK _BV(PD2)
47 #define EIMSK_BIT _BV(INT2)
48 #define EICRx_BIT (~(_BV(ISC20) | _BV(ISC21)))
49 #define SERIAL_PIN_INTERRUPT INT2_vect
50 #elif SOFT_SERIAL_PIN == D3
51 #define SERIAL_PIN_MASK _BV(PD3)
52 #define EIMSK_BIT _BV(INT3)
53 #define EICRx_BIT (~(_BV(ISC30) | _BV(ISC31)))
54 #define SERIAL_PIN_INTERRUPT INT3_vect
55 #endif
56 #elif SOFT_SERIAL_PIN == E6
57 #define SERIAL_PIN_DDR DDRE
58 #define SERIAL_PIN_PORT PORTE
59 #define SERIAL_PIN_INPUT PINE
60 #define SERIAL_PIN_MASK _BV(PE6)
61 #define EIMSK_BIT _BV(INT6)
62 #define EICRx_BIT (~(_BV(ISC60) | _BV(ISC61)))
63 #define SERIAL_PIN_INTERRUPT INT6_vect
64 #else
65 #error invalid SOFT_SERIAL_PIN value
66 #endif
67
68#else
69 #error serial.c now support ATmega32U4 only
70#endif
71
72//////////////// for backward compatibility ////////////////////////////////
73#ifndef SERIAL_USE_MULTI_TRANSACTION
74/* --- USE Simple API (OLD API, compatible with let's split serial.c) */
75 #if SERIAL_SLAVE_BUFFER_LENGTH > 0
76 uint8_t volatile serial_slave_buffer[SERIAL_SLAVE_BUFFER_LENGTH] = {0};
77 #endif
78 #if SERIAL_MASTER_BUFFER_LENGTH > 0
79 uint8_t volatile serial_master_buffer[SERIAL_MASTER_BUFFER_LENGTH] = {0};
80 #endif
81 uint8_t volatile status0 = 0;
82
83SSTD_t transactions[] = {
84 { (uint8_t *)&status0,
85 #if SERIAL_MASTER_BUFFER_LENGTH > 0
86 sizeof(serial_master_buffer), (uint8_t *)serial_master_buffer,
87 #else
88 0, (uint8_t *)NULL,
89 #endif
90 #if SERIAL_SLAVE_BUFFER_LENGTH > 0
91 sizeof(serial_slave_buffer), (uint8_t *)serial_slave_buffer
92 #else
93 0, (uint8_t *)NULL,
94 #endif
95 }
96};
97
98void serial_master_init(void)
99{ soft_serial_initiator_init(transactions, TID_LIMIT(transactions)); }
100
101void serial_slave_init(void)
102{ soft_serial_target_init(transactions, TID_LIMIT(transactions)); }
103
104// 0 => no error
105// 1 => slave did not respond
106// 2 => checksum error
107int serial_update_buffers()
108{
109 int result;
110 result = soft_serial_transaction();
111 return result;
112}
113
114#endif // end of Simple API (OLD API, compatible with let's split serial.c)
115////////////////////////////////////////////////////////////////////////////
116
117#define ALWAYS_INLINE __attribute__((always_inline))
118#define NO_INLINE __attribute__((noinline))
119#define _delay_sub_us(x) __builtin_avr_delay_cycles(x)
120
121// parity check
122#define ODD_PARITY 1
123#define EVEN_PARITY 0
124#define PARITY EVEN_PARITY
125
126#ifdef SERIAL_DELAY
127 // custom setup in config.h
128 // #define TID_SEND_ADJUST 2
129 // #define SERIAL_DELAY 6 // micro sec
130 // #define READ_WRITE_START_ADJUST 30 // cycles
131 // #define READ_WRITE_WIDTH_ADJUST 8 // cycles
132#else
133// ============ Standard setups ============
134
135#ifndef SELECT_SOFT_SERIAL_SPEED
136#define SELECT_SOFT_SERIAL_SPEED 1
137// 0: about 189kbps
138// 1: about 137kbps (default)
139// 2: about 75kbps
140// 3: about 39kbps
141// 4: about 26kbps
142// 5: about 20kbps
143#endif
144
145#if __GNUC__ < 6
146 #define TID_SEND_ADJUST 14
147#else
148 #define TID_SEND_ADJUST 2
149#endif
150
151#if SELECT_SOFT_SERIAL_SPEED == 0
152 // Very High speed
153 #define SERIAL_DELAY 4 // micro sec
154 #if __GNUC__ < 6
155 #define READ_WRITE_START_ADJUST 33 // cycles
156 #define READ_WRITE_WIDTH_ADJUST 3 // cycles
157 #else
158 #define READ_WRITE_START_ADJUST 34 // cycles
159 #define READ_WRITE_WIDTH_ADJUST 7 // cycles
160 #endif
161#elif SELECT_SOFT_SERIAL_SPEED == 1
162 // High speed
163 #define SERIAL_DELAY 6 // micro sec
164 #if __GNUC__ < 6
165 #define READ_WRITE_START_ADJUST 30 // cycles
166 #define READ_WRITE_WIDTH_ADJUST 3 // cycles
167 #else
168 #define READ_WRITE_START_ADJUST 33 // cycles
169 #define READ_WRITE_WIDTH_ADJUST 7 // cycles
170 #endif
171#elif SELECT_SOFT_SERIAL_SPEED == 2
172 // Middle speed
173 #define SERIAL_DELAY 12 // micro sec
174 #define READ_WRITE_START_ADJUST 30 // cycles
175 #if __GNUC__ < 6
176 #define READ_WRITE_WIDTH_ADJUST 3 // cycles
177 #else
178 #define READ_WRITE_WIDTH_ADJUST 7 // cycles
179 #endif
180#elif SELECT_SOFT_SERIAL_SPEED == 3
181 // Low speed
182 #define SERIAL_DELAY 24 // micro sec
183 #define READ_WRITE_START_ADJUST 30 // cycles
184 #if __GNUC__ < 6
185 #define READ_WRITE_WIDTH_ADJUST 3 // cycles
186 #else
187 #define READ_WRITE_WIDTH_ADJUST 7 // cycles
188 #endif
189#elif SELECT_SOFT_SERIAL_SPEED == 4
190 // Very Low speed
191 #define SERIAL_DELAY 36 // micro sec
192 #define READ_WRITE_START_ADJUST 30 // cycles
193 #if __GNUC__ < 6
194 #define READ_WRITE_WIDTH_ADJUST 3 // cycles
195 #else
196 #define READ_WRITE_WIDTH_ADJUST 7 // cycles
197 #endif
198#elif SELECT_SOFT_SERIAL_SPEED == 5
199 // Ultra Low speed
200 #define SERIAL_DELAY 48 // micro sec
201 #define READ_WRITE_START_ADJUST 30 // cycles
202 #if __GNUC__ < 6
203 #define READ_WRITE_WIDTH_ADJUST 3 // cycles
204 #else
205 #define READ_WRITE_WIDTH_ADJUST 7 // cycles
206 #endif
207#else
208#error invalid SELECT_SOFT_SERIAL_SPEED value
209#endif /* SELECT_SOFT_SERIAL_SPEED */
210#endif /* SERIAL_DELAY */
211
212#define SERIAL_DELAY_HALF1 (SERIAL_DELAY/2)
213#define SERIAL_DELAY_HALF2 (SERIAL_DELAY - SERIAL_DELAY/2)
214
215#define SLAVE_INT_WIDTH_US 1
216#ifndef SERIAL_USE_MULTI_TRANSACTION
217 #define SLAVE_INT_RESPONSE_TIME SERIAL_DELAY
218#else
219 #define SLAVE_INT_ACK_WIDTH_UNIT 2
220 #define SLAVE_INT_ACK_WIDTH 4
221#endif
222
223static SSTD_t *Transaction_table = NULL;
224static uint8_t Transaction_table_size = 0;
225
226inline static void serial_delay(void) ALWAYS_INLINE;
227inline static
228void serial_delay(void) {
229 _delay_us(SERIAL_DELAY);
230}
231
232inline static void serial_delay_half1(void) ALWAYS_INLINE;
233inline static
234void serial_delay_half1(void) {
235 _delay_us(SERIAL_DELAY_HALF1);
236}
237
238inline static void serial_delay_half2(void) ALWAYS_INLINE;
239inline static
240void serial_delay_half2(void) {
241 _delay_us(SERIAL_DELAY_HALF2);
242}
243
244inline static void serial_output(void) ALWAYS_INLINE;
245inline static
246void serial_output(void) {
247 SERIAL_PIN_DDR |= SERIAL_PIN_MASK;
248}
249
250// make the serial pin an input with pull-up resistor
251inline static void serial_input_with_pullup(void) ALWAYS_INLINE;
252inline static
253void serial_input_with_pullup(void) {
254 SERIAL_PIN_DDR &= ~SERIAL_PIN_MASK;
255 SERIAL_PIN_PORT |= SERIAL_PIN_MASK;
256}
257
258inline static uint8_t serial_read_pin(void) ALWAYS_INLINE;
259inline static
260uint8_t serial_read_pin(void) {
261 return !!(SERIAL_PIN_INPUT & SERIAL_PIN_MASK);
262}
263
264inline static void serial_low(void) ALWAYS_INLINE;
265inline static
266void serial_low(void) {
267 SERIAL_PIN_PORT &= ~SERIAL_PIN_MASK;
268}
269
270inline static void serial_high(void) ALWAYS_INLINE;
271inline static
272void serial_high(void) {
273 SERIAL_PIN_PORT |= SERIAL_PIN_MASK;
274}
275
276void soft_serial_initiator_init(SSTD_t *sstd_table, int sstd_table_size)
277{
278 Transaction_table = sstd_table;
279 Transaction_table_size = (uint8_t)sstd_table_size;
280 serial_output();
281 serial_high();
282}
283
284void soft_serial_target_init(SSTD_t *sstd_table, int sstd_table_size)
285{
286 Transaction_table = sstd_table;
287 Transaction_table_size = (uint8_t)sstd_table_size;
288 serial_input_with_pullup();
289
290 // Enable INT0-INT3,INT6
291 EIMSK |= EIMSK_BIT;
292#if SERIAL_PIN_MASK == _BV(PE6)
293 // Trigger on falling edge of INT6
294 EICRB &= EICRx_BIT;
295#else
296 // Trigger on falling edge of INT0-INT3
297 EICRA &= EICRx_BIT;
298#endif
299}
300
301// Used by the sender to synchronize timing with the reciver.
302static void sync_recv(void) NO_INLINE;
303static
304void sync_recv(void) {
305 for (uint8_t i = 0; i < SERIAL_DELAY*5 && serial_read_pin(); i++ ) {
306 }
307 // This shouldn't hang if the target disconnects because the
308 // serial line will float to high if the target does disconnect.
309 while (!serial_read_pin());
310}
311
312// Used by the reciver to send a synchronization signal to the sender.
313static void sync_send(void) NO_INLINE;
314static
315void sync_send(void) {
316 serial_low();
317 serial_delay();
318 serial_high();
319}
320
321// Reads a byte from the serial line
322static uint8_t serial_read_chunk(uint8_t *pterrcount, uint8_t bit) NO_INLINE;
323static uint8_t serial_read_chunk(uint8_t *pterrcount, uint8_t bit) {
324 uint8_t byte, i, p, pb;
325
326 _delay_sub_us(READ_WRITE_START_ADJUST);
327 for( i = 0, byte = 0, p = PARITY; i < bit; i++ ) {
328 serial_delay_half1(); // read the middle of pulses
329 if( serial_read_pin() ) {
330 byte = (byte << 1) | 1; p ^= 1;
331 } else {
332 byte = (byte << 1) | 0; p ^= 0;
333 }
334 _delay_sub_us(READ_WRITE_WIDTH_ADJUST);
335 serial_delay_half2();
336 }
337 /* recive parity bit */
338 serial_delay_half1(); // read the middle of pulses
339 pb = serial_read_pin();
340 _delay_sub_us(READ_WRITE_WIDTH_ADJUST);
341 serial_delay_half2();
342
343 *pterrcount += (p != pb)? 1 : 0;
344
345 return byte;
346}
347
348// Sends a byte with MSB ordering
349void serial_write_chunk(uint8_t data, uint8_t bit) NO_INLINE;
350void serial_write_chunk(uint8_t data, uint8_t bit) {
351 uint8_t b, p;
352 for( p = PARITY, b = 1<<(bit-1); b ; b >>= 1) {
353 if(data & b) {
354 serial_high(); p ^= 1;
355 } else {
356 serial_low(); p ^= 0;
357 }
358 serial_delay();
359 }
360 /* send parity bit */
361 if(p & 1) { serial_high(); }
362 else { serial_low(); }
363 serial_delay();
364
365 serial_low(); // sync_send() / senc_recv() need raise edge
366}
367
368static void serial_send_packet(uint8_t *buffer, uint8_t size) NO_INLINE;
369static
370void serial_send_packet(uint8_t *buffer, uint8_t size) {
371 for (uint8_t i = 0; i < size; ++i) {
372 uint8_t data;
373 data = buffer[i];
374 sync_send();
375 serial_write_chunk(data,8);
376 }
377}
378
379static uint8_t serial_recive_packet(uint8_t *buffer, uint8_t size) NO_INLINE;
380static
381uint8_t serial_recive_packet(uint8_t *buffer, uint8_t size) {
382 uint8_t pecount = 0;
383 for (uint8_t i = 0; i < size; ++i) {
384 uint8_t data;
385 sync_recv();
386 data = serial_read_chunk(&pecount, 8);
387 buffer[i] = data;
388 }
389 return pecount == 0;
390}
391
392inline static
393void change_sender2reciver(void) {
394 sync_send(); //0
395 serial_delay_half1(); //1
396 serial_low(); //2
397 serial_input_with_pullup(); //2
398 serial_delay_half1(); //3
399}
400
401inline static
402void change_reciver2sender(void) {
403 sync_recv(); //0
404 serial_delay(); //1
405 serial_low(); //3
406 serial_output(); //3
407 serial_delay_half1(); //4
408}
409
410static inline uint8_t nibble_bits_count(uint8_t bits)
411{
412 bits = (bits & 0x5) + (bits >> 1 & 0x5);
413 bits = (bits & 0x3) + (bits >> 2 & 0x3);
414 return bits;
415}
416
417// interrupt handle to be used by the target device
418ISR(SERIAL_PIN_INTERRUPT) {
419
420#ifndef SERIAL_USE_MULTI_TRANSACTION
421 serial_low();
422 serial_output();
423 SSTD_t *trans = Transaction_table;
424#else
425 // recive transaction table index
426 uint8_t tid, bits;
427 uint8_t pecount = 0;
428 sync_recv();
429 bits = serial_read_chunk(&pecount,7);
430 tid = bits>>3;
431 bits = (bits&7) != nibble_bits_count(tid);
432 if( bits || pecount> 0 || tid > Transaction_table_size ) {
433 return;
434 }
435 serial_delay_half1();
436
437 serial_high(); // response step1 low->high
438 serial_output();
439 _delay_sub_us(SLAVE_INT_ACK_WIDTH_UNIT*SLAVE_INT_ACK_WIDTH);
440 SSTD_t *trans = &Transaction_table[tid];
441 serial_low(); // response step2 ack high->low
442#endif
443
444 // target send phase
445 if( trans->target2initiator_buffer_size > 0 )
446 serial_send_packet((uint8_t *)trans->target2initiator_buffer,
447 trans->target2initiator_buffer_size);
448 // target switch to input
449 change_sender2reciver();
450
451 // target recive phase
452 if( trans->initiator2target_buffer_size > 0 ) {
453 if (serial_recive_packet((uint8_t *)trans->initiator2target_buffer,
454 trans->initiator2target_buffer_size) ) {
455 *trans->status = TRANSACTION_ACCEPTED;
456 } else {
457 *trans->status = TRANSACTION_DATA_ERROR;
458 }
459 } else {
460 *trans->status = TRANSACTION_ACCEPTED;
461 }
462
463 sync_recv(); //weit initiator output to high
464}
465
466/////////
467// start transaction by initiator
468//
469// int soft_serial_transaction(int sstd_index)
470//
471// Returns:
472// TRANSACTION_END
473// TRANSACTION_NO_RESPONSE
474// TRANSACTION_DATA_ERROR
475// this code is very time dependent, so we need to disable interrupts
476#ifndef SERIAL_USE_MULTI_TRANSACTION
477int soft_serial_transaction(void) {
478 SSTD_t *trans = Transaction_table;
479#else
480int soft_serial_transaction(int sstd_index) {
481 if( sstd_index > Transaction_table_size )
482 return TRANSACTION_TYPE_ERROR;
483 SSTD_t *trans = &Transaction_table[sstd_index];
484#endif
485 cli();
486
487 // signal to the target that we want to start a transaction
488 serial_output();
489 serial_low();
490 _delay_us(SLAVE_INT_WIDTH_US);
491
492#ifndef SERIAL_USE_MULTI_TRANSACTION
493 // wait for the target response
494 serial_input_with_pullup();
495 _delay_us(SLAVE_INT_RESPONSE_TIME);
496
497 // check if the target is present
498 if (serial_read_pin()) {
499 // target failed to pull the line low, assume not present
500 serial_output();
501 serial_high();
502 *trans->status = TRANSACTION_NO_RESPONSE;
503 sei();
504 return TRANSACTION_NO_RESPONSE;
505 }
506
507#else
508 // send transaction table index
509 int tid = (sstd_index<<3) | (7 & nibble_bits_count(sstd_index));
510 sync_send();
511 _delay_sub_us(TID_SEND_ADJUST);
512 serial_write_chunk(tid, 7);
513 serial_delay_half1();
514
515 // wait for the target response (step1 low->high)
516 serial_input_with_pullup();
517 while( !serial_read_pin() ) {
518 _delay_sub_us(2);
519 }
520
521 // check if the target is present (step2 high->low)
522 for( int i = 0; serial_read_pin(); i++ ) {
523 if (i > SLAVE_INT_ACK_WIDTH + 1) {
524 // slave failed to pull the line low, assume not present
525 serial_output();
526 serial_high();
527 *trans->status = TRANSACTION_NO_RESPONSE;
528 sei();
529 return TRANSACTION_NO_RESPONSE;
530 }
531 _delay_sub_us(SLAVE_INT_ACK_WIDTH_UNIT);
532 }
533#endif
534
535 // initiator recive phase
536 // if the target is present syncronize with it
537 if( trans->target2initiator_buffer_size > 0 ) {
538 if (!serial_recive_packet((uint8_t *)trans->target2initiator_buffer,
539 trans->target2initiator_buffer_size) ) {
540 serial_output();
541 serial_high();
542 *trans->status = TRANSACTION_DATA_ERROR;
543 sei();
544 return TRANSACTION_DATA_ERROR;
545 }
546 }
547
548 // initiator switch to output
549 change_reciver2sender();
550
551 // initiator send phase
552 if( trans->initiator2target_buffer_size > 0 ) {
553 serial_send_packet((uint8_t *)trans->initiator2target_buffer,
554 trans->initiator2target_buffer_size);
555 }
556
557 // always, release the line when not in use
558 sync_send();
559
560 *trans->status = TRANSACTION_END;
561 sei();
562 return TRANSACTION_END;
563}
564
565#ifdef SERIAL_USE_MULTI_TRANSACTION
566int soft_serial_get_and_clean_status(int sstd_index) {
567 SSTD_t *trans = &Transaction_table[sstd_index];
568 cli();
569 int retval = *trans->status;
570 *trans->status = 0;;
571 sei();
572 return retval;
573}
574#endif
575
576#endif
577
578// Helix serial.c history
579// 2018-1-29 fork from let's split and add PD2, modify sync_recv() (#2308, bceffdefc)
580// 2018-6-28 bug fix master to slave comm and speed up (#3255, 1038bbef4)
581// (adjusted with avr-gcc 4.9.2)
582// 2018-7-13 remove USE_SERIAL_PD2 macro (#3374, f30d6dd78)
583// (adjusted with avr-gcc 4.9.2)
584// 2018-8-11 add support multi-type transaction (#3608, feb5e4aae)
585// (adjusted with avr-gcc 4.9.2)
586// 2018-10-21 fix serial and RGB animation conflict (#4191, 4665e4fff)
587// (adjusted with avr-gcc 7.3.0)
588// 2018-10-28 re-adjust compiler depend value of delay (#4269, 8517f8a66)
589// (adjusted with avr-gcc 5.4.0, 7.3.0)
generated by cgit v1.2.3 (git 2.25.1) at 2025-11-22 19:31:43 +0000